1. System Requirements

Installation Steps: 1 2 3 4 5 6 7

The N7612C Signal Studio for TD-SCDMA/HSPA 2018 software can be installed on a PC for use with the N5172B EXG or N5182B MXG X-series signal generators. The PC software allows the user to configure settings, generates scenario data, and provides a user interface for real-time control of the signals being produced by the signal generators.

Instrument Requirements

Instruments

Requirements

N5172B EXG X-Series RF vector signal generator

Firmware:

  • Version B.01.75 or later

Required options:

  • N5172B-503 (9 kHz to 3 GHz frequency range)

  • N5172B-653 (internal baseband generator, 32 Msa/s, up to 60 MHz RF bandwidth)

  • N5172B-660 (upgrade baseband generator with real-time capability)

Recommended options:

  • N5172B-009 (internal Flash drive)

  • N5172B-403 (calibrated AWGN for testing with noise)

N5172B-660 is not required for the N7609B software's basic option.

N5182B MXG X-Series RF vector signal generator

Firmware:

  • Version B.01.75 or later

Required options:

  • N5182B-503 (9 kHz to 3 GHz frequency range)

  • N5182B-656 (internal baseband generator, 32 Msa/s, up to 80 MHz RF bandwidth)

  • N5182B-660 (upgrade baseband generator with real-time capability)

Recommended options:

  • N5182B-009 (internal Flash drive)

  • N5182B-1EQ (low power output for Rx testing)

  • N5182B-403 (calibrated AWGN for testing with noise)

  • N5182B-UNX (low phase noise)

N5182B-660 is not required for the N7609B software's basic option.

E8267D PSG vector signal generator

Firmware:

  • Version C.06.26 or later

Required options:

  • E8267D-520 (250 kHz to 20 GHz frequency range)

  • E8267D-602 (internal baseband generator with 64 Msa memory and digital bus capability)

Recommended options:

  • E8267D-005 (6 GB internal hard drive)

  • E8267D-403 (calibrated AWGN for testing with noise)

  • E8267D-UNR (enhanced phase noise performance)

M9381A PXIe vector signal generator

Driver:

  • Version 1.4.400.0 or later

Recommended options:

  • M9381A-F03 (1 MHz to 3 GHz frequency range)

  • M9381A-B04 (RF modulation bandwidth 40 MHz)

  • M9381A-M01 (memory 32 Msa)

  • M9381A-300 (adds M9300A PXIe frequency reference, if one is not already in the system)

Limitations:

The M9381A VSG has a limitation related to the Power Search and DC Cal functions, creating a time-synchronization loss. That is, the signal timing changes after a Power Search or DC Cal. When ALC is set to Off, Signal Studio automatically runs Power Search, which affects the user's trigger signal for starting waveform playback. Even though the timing alignment of the trigger signal and waveform are properly set, the Power Search function disrupts this synchronization. In these cases, use the following workarounds:

  • Set ALC to On whenever possible. This avoids the automatic Power Search.

  • When ALC must be set to Off (or is set to Off by Signal Studio), you can re-trigger the signal by turning ARB Off, then On, and then send the trigger signal to M9381A VSG.

For DC Cal, run it before you download and play the waveform. Do not run DC Cal while the signal is playing, which disrupts the synchronization.

E6640A EXM wireless test set

Software:

  • Version E.16.06 or later

Recommended options:

  • E6640A-B85 (increases signal bandwidth to 80 MHz)

  • E6640A-B1X (increases signal bandwidth to 160 MHz)

PC Requirements

200 GB HDD with 2 GB free disk space at runtime (5 GB or higher recommended)

1024 x 768 screen resolution (1280 x 1024 recommended)

If you use a high-resolution display, the GUI's font size may appear too small to read. To resolve this, lower your PC's display resolution, but make sure the display scaling remains set at 100 percent, otherwise portions of the GUI will become truncated and hidden from view.

Windows 10 (64 bit):

Windows 7 (64 bit):

Microsoft .NET Framework 4.5.2 or later

Keysight IO Libraries, version 18.0 or later

Keysight License Manager 5 (4. Downloading and Installing Keysight License Manager 5)

Keysight License Service (included with installer)

Keysight Host Processor Platform (included with installer)

Installed GPIB IO interface card, LAN interface card, or USB/GPIB interface connector

Keysight VISA

Microsoft Windows Installer version 2.0 or later

In order for the N7612C Signal Studio for TD-SCDMA/HSPA 2018 software to generate signals, you must have a properly configured PC and properly configured signal generation hardware, all of which meet the system requirements.

Hardware Requirements for TD-SCDMA/HSPA

Instruments

Requirements

N5172B EXG X-Series RF vector signal generator

Firmware:

  • Version B.01.70 or later

Required options:

  • N5172B-503 (9 kHz to 3 GHz frequency range)

  • N5172B-653 (internal baseband generator, 32 Msa/s, up to 60 MHz RF bandwidth)

  • N5172B-660 (upgrade baseband generator with real-time capability)

Recommended options:

  • N5172B-009 (internal Flash drive)

  • N5172B-1EA (high power output for PA testing)

  • N5172B-1ER (flexible reference input, 1-50 MHz)

  • N5172B-403 (calibrated AWGN for testing with noise)

  • N5172B-655 (upgrade baseband generator from 60 to 120 MHz RF bandwidth)

  • N5172B-UNV (enhanced dynamic range)

  • N5172B-UNZ (fast switching for manufacturing environments)

N5182B MXG X-Series RF vector signal generator

Firmware:

  • Version B.01.70 or later

Required options:

  • N5182B-503 (9 kHz to 3 GHz frequency range)

  • N5182B-656 (internal baseband generator, 32 Msa/s, up to 80 MHz RF bandwidth)

  • N5182B-660 (upgrade baseband generator with real-time capability)

Recommended options:

  • N5182B-009 (internal Flash drive)

  • N5182B-1EA (high power output for PA testing)

  • N5182B-1ER (flexible reference input, 1-50 MHz)

  • N5182B-1EQ (low power output for Rx testing)

  • N5182B-403 (calibrated AWGN for testing with noise)

  • N5182B-657 (upgrade baseband generator from 80 to 160 MHz RF bandwidth)

  • N5182B-UNV (enhanced dynamic range)

  • N5182B-UNZ (fast switching for manufacturing environments)

N5182A MXG vector signal generator 

Firmware:

  • Version A.01.10 or later

One of the following baseband generator options:

  • N5182A-652 (60 Msa/s internal baseband generator with 8 Msa memory)

  • N5182A-654 (125 Msa/s internal baseband generator with 8 Msa memory, recommended)

One of the following frequency options:

  • Option 503 (250 kHz to 3 GHz frequency range) 

  • Option 506 (250 kHz to 6 GHz frequency range, recommended)

Recommended options:

  • N5182A-019 (increase baseband generator memory to 64 Msa memory)

  • N5182A-403 (calibrated noise personality, required for C/N capability)

  • N5182A-UNV (enhanced dynamic range)

E4438C ESG vector signal generator 

Firmware:

  • Version C.04.84 or later

One of the following baseband generator options:

  • E4438C-001 (internal baseband generator with 8 Msa memory)

  • E4438C-002 (internal baseband generator with 32 Msa memory)

  • E4438C-601 (internal baseband generator with 8 Msa memory and digital bus capability)

  • E4438C-602 (internal baseband generator with 64 Msa memory and digital bus capability, recommended)

One of the following frequency options:

  • E4438C-503 (250 kHz to 3 GHz frequency range)

  • E4438C-504 (250 kHz to 4 GHz frequency range)

  • E4438C-506 (250 kHz to 6 GHz frequency range, recommended)

Recommended options:

  • E4438C-005 (6 GB internal hard drive)

  • E4438C-403 (calibrated noise personality, required for C/N capability)

  • E4438C-UNJ (enhanced phase noise performance)

M9381A PXIe vector signal generator

Driver:

  • Version 1.4.400.0 or later

Recommended options:

  • M9381A-M05 (memory 512 Msa)

  • M9381A-M10 (memory 1024 Msa)

  • M9381A-1EA (high output power)

  • M9381A-B10 (RF modulation bandwidth 100 MHz)

  • M9381A-B16 (RF modulation bandwidth 160 MHz)

Additional options to consider:

  • M9381A-F06 (frequency range 1 MHz to 6 GHz)

Limitations:

The M9381A VSG has a limitation related to the Power Search and DC Cal functions, creating a time-synchronization loss. That is, the signal timing changes after a Power Search or DC Cal. When ALC is set to Off, Signal Studio automatically runs Power Search, which affects the user's trigger signal for starting waveform playback. Even though the timing alignment of the trigger signal and waveform are properly set, the Power Search function disrupts this synchronization. In these cases, use the following workarounds:

  • Set ALC to On whenever possible. This avoids the automatic Power Search.

  • When ALC must be set to Off (or is set to Off by Signal Studio), you can re-trigger the signal by turning ARB Off, then On, and then send the trigger signal to M9381A VSG.

For DC Cal, run it before you download and play the waveform. Do not run DC Cal while the signal is playing, which disrupts the synchronization.

E6640A EXM wireless test set

Software:

  • Version E.16.06 or later

Recommended options:

  • E6640A-B85 (increases signal bandwidth to 80 MHz)

  • E6640A-B1X (increases signal bandwidth to 160 MHz)

  • Y-Options (these option models, beginning with "Y," combine signal creation and measurement applications)

Additional options to consider:

  • E6640A-506 (380 MHz to 6 GHz frequency range)

  • E6640A-5WC (frequency range for wireless connectivity)

M9420A VXT PXIe vector transceiver

Software:

  • Version M.16 or later

Recommended options:

  • M9420A-1EA (high output power)

  • M9420A-B85 (increases signal bandwidth to 80 MHz)

  • M9420A-B1X (increases signal bandwidth to 160 MHz)

  • M9420A-M05 (memory 512 Msa)

Additional options to consider:

  • M9420A-506 (6 GHz frequency range)

  • M9420A-FDX (full duplex ports)

  • M9420A-HDX (half duplex ports)

M9421A VXT PXIe vector transceiver

Software:

  • Version M.16 or later

Recommended options:

  • M9421A-1EA (high output power)

  • M9421A-B85 (increases signal bandwidth to 80 MHz)

  • M9421A-B1X (increases signal bandwidth to 160 MHz)

  • M9421A-M05 (memory 512 Msa)

Additional options to consider:

  • M9421A-506 (6 GHz frequency range)

  • M9421A-HDX (half duplex ports)

PC Requirements

200 GB HDD with 2 GB free disk space at runtime (5 GB or higher recommended)

1024 x 768 screen resolution (1280 x 1024 recommended)

If you use a high-resolution display, the GUI's font size may appear too small to read. To resolve this, lower your PC's display resolution, but make sure the display scaling remains set at 100 percent, otherwise portions of the GUI will become truncated and hidden from view.

Windows 10 (64 bit):

Windows 7 (64 bit):

Microsoft .NET Framework 4.5.2 or later

Keysight IO Libraries, version 18.0 or later

Keysight License Manager 5 (4. Downloading and Installing Keysight License Manager 5)

Keysight License Service (included with installer)

Keysight Host Processor Platform (included with installer)

Installed GPIB IO interface card, LAN interface card, or USB/GPIB interface connector

Keysight VISA

Microsoft Windows Installer version 2.0 or later