CALL:SHANdoff

Function

Turns Soft Handover On or Off. (See Enabling Soft Handover )

Setting

Range: 0|OFF|1|ON

Query

Range: 0|1

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:ENABle ON" 
!Turns Soft Handover ON.

Function

Turns Event State On or Off (enables/disables event reporting). (See Event Reporting )

Setting

Range: 0|OFF|1|ON

Query

Range: 0|1

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EVENt:ENABle ON" 
!Turns Event State ON.

Function

Sends a Measurement Control message. You must send this command after configuring an event parameter (CALL:SHANdoff:EVent1A - 1F commands) for the new event parameter value to be implemented by the UE. (See Event Reporting ).

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EVENt:SEND:CONFig" 
!Sends a Measurement Control message.

Function

Controls the UTRA FDD Event 1a ON/OFF State. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

It is recommended that you set CALL:SHANdoff:EVENt:ENABle to OFF before changing this setting. You must then turn CALL:SHANdoff:EVENt:ENABle back ON to enable event reporting.

Setting

Range: 0|OFF|1|ON

Query

Range: 0|1

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1A:STATe ON" 
!Turns the Event 1a State ON.

Function

Controls the UTRA FDD Event 1a Reporting Range Constant. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

Setting

Range: 0.0 to 14.5 dB

Resolution: 0.5 dB

Query

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1A:REPorting:RANGe 3" 
!Sets the UTRA FDD Event 1a Reporting Range Constant to 3 dB.

Function

Controls the UTRA FDD Event 1a Hysteresis. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

Setting

Range: 0.0 dB to 7.5 dB

Resolution: 0.5 dB

Query

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1A:HYSTeresis 4" 
!Sets the UTRA FDD Event 1a Hysteresis to 4 dB.

Function

Controls the UTRA FDD Event 1a "W" Value. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

Setting

Range: 0.0 to 2.0

Resolution: 0.1

Query

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1A:WVALue 0.5" 
!Sets the UTRA FDD Event 1a "W" Value to 0.5.

Function

Controls the UTRA FDD Event 1b ON/OFF State. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

It is recommended that you set CALL:SHANdoff:EVENt:ENABle to OFF before changing this setting. You must then turn CALL:SHANdoff:EVENt:ENABle back ON to enable event reporting.

Setting

Range: 0|OFF|1|ON

Query

Range: 0|1

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1B:STATe ON" 
!Turns the Event 1b State ON.

Function

Controls the UTRA FDD Event 1b Reporting Range Constant. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

Setting

Range: 0.0 to 14.5 dB

Resolution: 0.5 dB

Query

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1B:REPorting:RANGe 3" 
!Sets the UTRA FDD Event 1b Reporting Range Constant to 3 dB.

Function

Controls the UTRA FDD Event 1b Hysteresis. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

Setting

Range: 0.0 dB to 7.5 dB

Resolution: 0.5 dB

Query

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1B:HYSTeresis 4" 
!Sets the UTRA FDD Event 1b Hysteresis to 4.0 dB.

Function

Controls the UTRA FDD Event 1b "W" Value. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

Setting

Range: 0.0 to 2.0

Resolution: 0.1

Query

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1B:WVALue 5" 
!Sets the UTRA FDD Event 1b "W" Value to 0.5 dB.

Function

Controls the UTRA FDD Event 1c ON/OFF State. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

It is recommended that you set CALL:SHANdoff:EVENt:ENABle to OFF before changing this setting. You must then turn CALL:SHANdoff:EVENt:ENABle back ON to enable event reporting.

Setting

Range: 0|OFF|1|ON

Query

Range: 0|1

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1C:STATe ON" 
!Turns the Event 1c State ON.

Function

Controls the UTRA FDD Event 1c Hysteresis. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

Setting

Range: 0.0 dB to 7.5 dB

Resolution: 0.5 dB

Query

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1C:HYSTeresis 4" 
!Sets the UTRA FDD Event 1c Hysteresis to 4.0 dB.

Function

Controls the UTRA FDD Event 1d ON/OFF State. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

It is recommended that you set CALL:SHANdoff:EVENt:ENABle to OFF before changing this setting. You must then turn CALL:SHANdoff:EVENt:ENABle back ON to enable event reporting.

Setting

Range: 0|OFF|1|ON

Query

Range: 0|1

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1D:STATe ON" 
!Turns the Event 1d State ON.

Function

Controls the UTRA FDD Event 1c Hysteresis. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

Setting

Range: 0.0 dB to 7.5 dB

Resolution: 0.5 dB

Query

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1D:HYSTeresis 4" 
!Sets the UTRA FDD Event 1d Hysteresis to 4.0 dB.

Function

Controls the UTRA FDD Event 1e ON/OFF State. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

It is recommended that you set CALL:SHANdoff:EVENt:ENABle to OFF before changing this setting. You must then turn CALL:SHANdoff:EVENt:ENABle back ON to enable event reporting.

Setting

Range: 0|OFF|1|ON

Query

Range: 0|1

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1E:STATe ON" 
!Turns the Event 1e State ON.

Function

Controls the UTRA FDD Event 1e Hysteresis. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

Setting

Range: 0.0 dB to 7.5 dB

Resolution: 0.5 dB

Query

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1E:HYSTeresis 4" 
!Sets the UTRA FDD Event 1e Hysteresis to 4.0 dB.

Function

Controls the UTRA FDD Event 1e Threshold. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

Setting

Range: -115 to -25 dBm

Resolution: 1

Query

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1E:THREshold -70" 
!Sets the UTRA FDD Event 1e Threshold to -70 dBm.

Function

Controls the UTRA FDD Event 1f ON/OFF State. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

It is recommended that you set CALL:SHANdoff:EVENt:ENABle to OFF before changing this setting. You must then turn CALL:SHANdoff:EVENt:ENABle back ON to enable event reporting.

Setting

Range: 0|OFF|1|ON

Query

Range: 0|1

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1F:STATe ON" 
!Turns the Event 1f State ON.

Function

Controls the UTRA FDD Event 1f Hysteresis. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

Setting

Range: 0.0 dB to 7.5 dB

Resolution: 0.5

Query

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1F:HYSTeresis 4" 
!Sets the UTRA FDD Event 1f Hysteresis to 4.0 dB.

Function

Controls the UTRA FDD Event 1f Threshold. In order for changes to this event parameter to be seen by the UE, you must send the CALL:SHANdoff:EVENt:SEND:CONFig command. (See Event Reporting ).

Setting

Range: -115 to -25 dBm

Resolution: 1

Query

*RST Setting

Programming Example

 
OUTPUT 714;"CALL:SHANdoff:EV1F:THREshold -70" 
!Sets the UTRA FDD Event 1f Threshold to -70 dBm.