Setup Commands - Noise Figure Measurement Class

Only the Main and Layout Setup commands corresponding to the Noise Figure measurement class are documented here. All other commands are identical to the Setup commands for the Standard measurement class and can be accessed by clicking here or by clicking on the softtabs on the graphic below.

Click here to view links to Setup commands for all Measurement Classes.

Main

Layout

System
Setup

Internal
Hardware

External
Hardware

Main Tab Commands
Softkey	Sub-item	SCPI
NF Setup...	Frequency
	Sweep Type
	Linear Sweep	SENSe:SWEep:TYPE
	Log Sweep	SENSe:SWEep:TYPE
	CW Frequency	SENSe:SWEep:TYPE
	Segment Sweep	SENSe:SWEep:TYPE
	Sweep Settings
	Number of Points	SENSe:SWEep:POINts
	IF Bandwidth	SENSe:BWIDth[:RESolution]
	Start	SENSe:FREQuency:STARt
	Stop	SENSe:FREQuency:STOP
	Center	SENSe:FREQuency:CENTer
	Span	SENSe:FREQuency:SPAN
	Power
	Power On (All Channels)	OUTPut[:STATe]
	DUT Input Port
	Input Port	SENSe:NOISe:PMAP
	Power Level	SOURce:POWer[:LEVel][:IMMediate][:AMPLitude]
	Source Leveling Mode	SOURce:POWer:ALC[:MODE]
	DUT Output Port
	Output Port	SENSe:NOISe:PMAP
	Power Level	SOURce:POWer[:LEVel][:IMMediate][:AMPLitude]
	Source Leveling Mode	SOURce:POWer:ALC[:MODE]
	Path Configuration...	SENSe:PATH:CONFig:ELEMent[:STATe]
	Noise Figure
	Bandwidth/Average
	Noise Bandwidth	SENSe:NOISe:BWIDth[:RESolution]
	Average Number	SENSe:NOISe:AVERage[:COUNt]
	Average ON	SENSe:NOISe:AVERage:STATe
	Use Narrowband Compensation	SENSe:NOISe:NARRowband[:STATe]
	Noise Receiver
	External Noise Amplifier	SENSe:NOISe:AMPLifier
	NA Receiver (Port 2)	SENSe:NOISe:RECeiver
	Noise Receiver	SENSe:NOISe:RECeiver
	Receiver Gain	SENSe:NOISe:GAIN
	Source Temperature	SENSe:NOISe:TEMPerature:SOURce SENSe:NOISe:TEMPerature:SOURce:AUTO
	Ambient Temperature	SENSe:NOISe:TEMPerature:AMBient
	Impedance States
Max Acquired Impedance States	SENSe:NOISe:IMPedance:COUNt
Meas Class...		CALCulate:MEASure:DEFine
Quick Start...	S-Param	CALCulate:MEASure:PARameter
	Balanced	CALCulate:MEASure:PARameter
	Other	CALCulate:MEASure:PARameter
Layout Tab Commands
Softkey	Sub-item	SCPI
New Trace		DISPlay:WINDow:TRACe[:STATe]
New Channel		None
New Window		DISPlay:WINDow[:STATe]
New Sheet		DISPlay:SHEet:STATe
Delete	TrN	DISPlay:WINDow:TRACe:DELete
	ChN	SYSTem:CHANnels:DELete
	WinN	DISPlay:WINDow[:STATe]
Select	TrN	DISPlay:WINDow:TRACe:SELect
	ChN	None
	WinN	DISPlay:WINDow:TRACe:SELect
Measure...		CALCulate:MEASure:PARameter
Meas Class...		CALCulate:MEASure:DEFine