CALL:DPCHannel

Last updated: November 12, 2010

CALL:DPCHannel[:SLEVel]

Function	Sets/queries the dedicated physical channel's (DPCH) initial downlink offset, and sets its state to ON. This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: -30.00 dB to 0 dB (Prior to A.03, the range is -20.00 dB to 0 dB) Resolution: 0.01
Query	Range: -30.00 dB to 0 dB (Prior to A.03, the range is -20.00 dB to 0 dB) Resolution: 0.01
*RST Setting	-12.00 dB (off)
Requirements	Test Application Revision: A.03 and above Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:SLEVEL -12"

CALL[:CELL]:DPCHannel:ASET:ADD:AUX

Function

Performs an Add DPCH (Aux Node) to Active Set event.

The purpose of this event is to create a DPCH on the Aux node and signal to the UE to add it to the active set. This event is only valid when Multi-Cell UTRAN mode is active and a call is active on the Main node but no DPCH is currently assigned on the Aux node.If the operation is successful, the Multi-Cell UTRAN Status of the Aux node will change from "Aux" to "A-Act" to indicate dedicated channels are now assigned.

Requirements

Lab Application Revision: F.01 and above.

Programming Example

 
OUTPUT 714;"CALL:DPCHannel:ASET:ADD:AUX"

CALL[:CELL]:DPCHannel:ASET:ADD:MAIN

Function

Performs an Add DPCH (Main Node) to Active Setevent.

The purpose of this event is to create a DPCH on the main node and signal to the UE to add it to the active set. This event is only valid when Multi-Cell UTRAN mode is active and a call is active on an Aux node but no DPCH is currently assigned from the Main node.If the operation is successful, the Multi-Cell UTRAN Status of the main node will change from "M-Ext" to "M-SHO" to indicate dedicated channels are now assigned on both nodes

Requirements

Lab Application Revision: F.01 and above.

Programming Example

 
OUTPUT 714;"CALL:DPCHannel:ASET:ADD:MAIN"

CALL[:CELL]:DPCHannel:ASET:REMove:AUX

Function

Performs a Remove DPCH (Aux Node) from Active Set event.

The purpose of this event is to release the DPCH on the Aux node and signal to the UE to remove it from the active set. This event is only valid when Multi-Cell UTRAN mode is enabled and a call is active in which a DPCH from both the Main node and Aux node is present in the active set .If the operation is successful, the Aux node DPCH will be released and the Multi-Cell UTRAN Status will change from "A-Act" to "Aux". Meanwhile the status on the Main node will change to "M-Loc" indicating channels are only active on the Main node.

Requirements

Lab Application Revision: F.01 and above.

Programming Example

 
OUTPUT 714;"CALL:DPCHannel:ASET:REMove:AUX"

CALL[:CELL]:DPCHannel:ASET:REMove:MAIN

Function

Performs an Remove DPCH (Main Node) from Active Set event.

The purpose of this event is to release the DPCH on the main node and signal to the UE to remove it from the active set. This event is only valid when Multi-Cell UTRAN mode is enabled and a call is active in which a DPCH from both the Main node and Aux node is present in the active set.

If the operation is successful, the Main node DPCH will be released and the Multi-Cell UTRAN Status will change from "M-SHO" to "M-Ext". Meanwhile the status on the Aux node will remain at "A-Act" indicating channels are still active on the Aux node.

Requirements

Lab Application Revision: F.01 and above.

Programming Example

 
OUTPUT 714;"CALL:DPCHannel:ASET:REMove:MAIN"

CALL:DPCHannel:DOFFset

Function	Sets/queries Default DPCH Offset (DOFF) . This setting cannot be changed when the data/call status is not idle.
Setting	Range: 0 to 75 Resolution: 1
Query	Same as setting
*RST Setting	0 (0 x 512 chips)
Requirements	Test Application Revision: A.08.20 and above Lab Application Revision: C.03 and above Test Application Revision: A.17.00 and above, extend the range from 5 to 75 Lab Application Revision: G.01.00 and above, extend the range from 5 to 75
Programming Example OUTPUT 714;"CALL:DPCHANNEL:DOFFset 3" ! Sets Default DPCH Offset (DOFF) to 3 x 512 chips.

CALL:DPCHannel:KSPS15[:CCODe]

Function	THIS COMMAND IS OBSOLETE. Please use CALL:DPCHannel:KSPS15[:CCODe]:CODE . Sets/queries the channelization code for the downlink DPCH with a physical data rate of 15 ksps.
Setting	Range: CODE12\|CODE13\|CODE20\|CODE21\|CODE40\|CODE43\|CODE58 \|CODE126\|CODE127\|CODE142\|CODE153\|CODE174\|CODE235\|CODE255
Query	Same as setting
*RST Setting	CODE12
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:KSPS15:CCODE CODE13"

CALL:DPCHannel:KSPS15[:CCODe]:CODE

Function	Sets/queries the channelization code for the downlink DPCH with a physical data rate of 15 ksps. Codes 0 and 1 are reserved for the CPICH and SCH/PCCPCH respectively. See Downlink Channel Codes . This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: 2 to 255 Resolution: 1
Query	Same as setting
*RST Setting	12
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:KSPS15:CODE 12"

CALL:DPCHannel:KSPS15[:CCODe]:CODE:HSDPa

Function	Sets/queries the HSDPA/HSPA DPCH 15 ksps (OVSF 256) Channelization Code. See Downlink Channel Codes . This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: 2 to 255 Resolution: 1
Query	Same as setting
*RST Setting	40
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above, with the required feature license
Programming Example OUTPUT 714;"CALL:DPCHannel:KSPS15:CODE:HSDPa 40"

CALL:DPCHannel:KSPS15[:CCODe]:HSDPa

Function	THIS COMMAND IS OBSOLETE. Please use CALL:DPCHannel:KSPS15[:CCODe]:CODE:HSDPa . Sets/queries the HSDPA/HSPA DPCH 15 ksps (OVSF 256) Channelization Code.
Setting	Range: CODE40\|CODE43\|CODE58
Query	Same as setting
*RST Setting	CODE40
Requirements	Lab Application Revision: D.00 and above
Programming Example OUTPUT 714;"CALL:DPCHannel:KSPS15:HSDPa CODE43"

CALL:DPCHannel:KSPS30[:CCODe]

Function	THIS COMMAND IS OBSOLETE. Please use CALL:DPCHannel:KSPS30[:CCODe]:CODE . Sets/queries the channelization code for the downlink DPCH with a physical data rate of 30 ksps.
Setting	Range: CODE6\|CODE9\|CODE10\|CODE20\|CODE29\|CODE37\|CODE45 \|CODE54\|CODE60\|CODE63\|CODE70\|CODE76\|CODE87\|CODE93 \|CODE112\|CODE118
Query	Same as setting
*RST Setting	CODE9
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:KSPS30:CCODE CODE10"

CALL:DPCHannel:KSPS30[:CCODe]:CODE

Function	Sets/queries the channelization code for the downlink DPCH with a physical data rate of 30 ksps. See Downlink Channel Codes . This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: 1 to 127 Resolution: 1
Query	Same as setting
*RST Setting	9
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:KSPS30:CODE 9"

CALL:DPCHannel:KSPS30[:CCODe]:CODE:HSDPa

Function	Sets/queries the HSDPA/HSPA DPCH 30 ksps (OVSF 128) Channelization Code. See Downlink Channel Codes . This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use cell off operating mode when changing this value.
Setting	Range: 1 to 127
Query	Same as setting
*RST Setting	20
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above, with the required feature license
Programming Example OUTPUT 714;"CALL:DPCHANNEL:KSPS30:CODE:HSDPa 20"

CALL:DPCHannel:KSPS30[:CCODe]:HSDPa

Function	THIS COMMAND IS OBSOLETE. Please use CALL:DPCHannel:KSPS30[:CCODe]:HSDPa . Sets/queries the HSDPA/HSPA DPCH 30 ksps (OVSF 128) Channelization Code.
Setting	Range: CODE20\|CODE29\|CODE37\|CODE45\|CODE54
Query	Same as setting
*RST Setting	CODE20
Requirements	Lab Application Revision: C.03 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:KSPS30:HSDPa CODE29"

CALL:DPCHannel:KSPS60[:CCODe]:CODE

Function	Sets/queries the channelization code for the downlink DPCH with a physical data rate of 60 ksps. See Downlink Channel Codes . This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: 1 to 63 Resolution: 1
Query	Same as setting
*RST Setting	54
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above
Programming Example OUTPUT 714;"CALL:DPCHannel:KSPS60:CODE 54"

CALL:DPCHannel:KSPS120[:CCODe]

Function	THIS COMMAND IS OBSOLETE. Please use CALL:DPCHannel:KSPS120[:CCODe]:CODE . Sets/queries the channelization code for the downlink DPCH with a physical data rate of 120 ksps.
Setting	Range: CODE6\|CODE10\|CODE12\|CODE14\|CODE16\|CODE18 \|CODE20\|CODE22\|CODE24\|CODE25\|CODE26\|CODE27
Query	Same as setting
*RST Setting	CODE6
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:KSPS120 CODE10"

CALL:DPCHannel:KSPS120[:CCODe]:CODE

Function	Sets/queries the channelization code for the downlink DPCH with a physical data rate of 120 ksps. See Downlink Channel Codes . This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range:1 to 31 Resolution: 1
Query	Same as setting
*RST Setting	6
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above
Programming Example OUTPUT 714;"CALL:DPCHannel:KSPS120:CODE 6"

CALL:DPCHannel:KSPS240[:CCODe]

Function	THIS COMMAND IS OBSOLETE. Please use CALL:DPCHannel:KSPS240[:CCODe]:CODE . Sets/queries the channelization code for the downlink DPCH with a physical data rate of 240 ksps.
Setting	Range: CODE12\|CODE13
Query	Same as setting
*RST Setting	CODE12
Requirements	Lab Application Revision: B.01 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:KSPS240:CCODE CODE13" ! Sets the 240 ksps channelization code to 13.

CALL:DPCHannel:KSPS240[:CCODe]:CODE

Function	Sets/queries the channelization code for the downlink DPCH with a physical data rate of 240 ksps. See Downlink Channel Codes . This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range:1 to 15 Resolution: 1
Query	Same as setting
*RST Setting	12
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above
Programming Example OUTPUT 714;"CALL:DPCHannel:KSPS240:CODE 12"

CALL:DPCHannel:KSPS480[:CCODe]

Function	THIS COMMAND IS OBSOLETE. Please use CALL:DPCHannel:KSPS480[:CCODe]:CODE . Sets/queries the channelization code for the downlink DPCH with a physical data rate of 480 ksps.
Setting	Range: CODE6
Query	Same as setting
*RST Setting	CODE6
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:KSPS480:CCODE CODE6"

CALL:DPCHannel:KSPS480[:CCODe]:CODE

Function	Sets/queries the channelization code for the downlink DPCH with a physical data rate of 480 ksps. See Downlink Channel Codes . This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range:6
Query	Same as setting
*RST Setting	6
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above
Programming Example OUTPUT 714;"CALL:DPCHannel:KSPS480:CODE 6"

CALL:DPCHannel:LEVel

Function	Sets/queries the dedicated physical channel's (DPCH) initial downlink offset. This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: -30.00 dB to 0 dB (Prior to A.03, the range is -20.00 dB to 0 dB) Resolution: 0.01
Query	Range: -30.00 dB to 0 dB (Prior to A.03, the range is -20.00 dB to 0 dB) Resolution: 0.01
*RST Setting	-12.00 dB
Requirements	Test Application Revision: A.03 and above Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:LEVEL -12"

CALL:DPCHannel:RMC12:CCODe

Function	Sets/queries the dedicated physical control channel's channelization code for the 12.2 kbps reference measurement channel, the 12.2k AMR Voice channel, 33k No Coding RMC and 13.6k DCCH (SRB). See Downlink Channel Codes . This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: CODE6\|CODE9\|CODE10\|CODE20\|CODE29\|CODE37\|CODE45 \|CODE54\|CODE60\|CODE63\|CODE70\|CODE76\|CODE87\|CODE93 \|CODE112\|CODE118
Query	Range: CODE6\|CODE9\|CODE10\|CODE20\|CODE29\|CODE37\|CODE45 \|CODE54\|CODE60\|CODE63\|CODE70\|CODE76\|CODE87\|CODE93 \|CODE112\|CODE118
*RST Setting	CODE9
Requirements	Test Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:RMC12:CCODE CODE6" ! Sets the 12.2 RMC's channelization code.

CALL:DPCHannel:RMC12:CCODe:HSDPa

Function	Sets/queries the HSDPA/HSPA DPCH 12.2k RMC Channelization Code. See Downlink Channel Codes and HSDPA in FDD Test Operating Mode . This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: CODE20\|CODE29\|CODE37\|CODE45\|CODE54
Query	Same as setting
*RST Setting	CODE20
Requirements	Test Application Revision: A.08 and above, with the required feature license Lab Application Revision: C.03 and above.
Programming Example OUTPUT 714;"CALL:DPCHannel:RMC12:CCODe:HSDPa CODE29" ! Sets the HSDPA DPCH 12.2k RMC channelization code.

CALL:DPCHannel:RMC64:CCODe

Function	Sets/queries the dedicated physical control channel's 64 kbps reference measurement channel's channelization code. The type of bearer service being carried by the WCDMA link drives the configuration of the DTCH and DCCH logical channels, the DCH Transport channel, and the DPCH physical channel. The test set supports only symmetrical channels, and only one type of bearer service at a time. This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: CODE6\|CODE10\|CODE12\|CODE14\|CODE16\|CODE18 \|CODE20\|CODE22\|CODE24\|CODE25\|CODE26\|CODE27
Query	Same as setting
*RST Setting	CODE6
Requirements	Test Application Revision: A.02 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:RMC64:CCODE CODE10" ! Sets the 64 RMC's channelization code.

CALL:DPCHannel:RMC144:CCODe

Function	Sets/queries the DPCH 144k RMC Channelization Code (see Downlink Channel Codes ). This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: CODE12\|CODE13
Query	Same as setting
*RST Setting	CODE12
Requirements	Test Application Revision: A.05 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:RMC144:CCODE CODE13" ! Sets the 144k RMC's channelization code to 13.

CALL:DPCHannel:RMC384:CCODe

Function	Sets/queries the dedicated physical control channel's 384 kbps reference measurement channel's channelization code. The type of bearer service being carried by the WCDMA link drives the configuration of the DTCH and DCCH logical channels, the DCH Transport channel, and the DPCH physical channel. The test set supports only symmetrical channels, and only one type of bearer service at a time. This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: CODE6
Query	Same as setting
*RST Setting	CODE6
Requirements	Test Application Revision: A.04 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:RMC384:CCODE CODE6" ! Sets the 384k RMC's channelization code.

CALL:DPCHannel:STATe

Function	Sets/queries the dedicated physical control channel's state. This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: 1\|ON \| 0\|OFF
Query	Range: 1\|ON \| 0\|OFF
*RST Setting	0 (off)
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:DPCHANNEL:STAT 1"

CALL:DPCHannel:TYPe

Function	THIS COMMAND IS OBSOLETE. Please use the CALL:SERVice:RBTest:RAB command to set/query channel type. Sets/queries the dedicated physical control channel's channel type. See Channel Type . This setting cannot be changed while in active cell operating mode. Attempting to change this setting while in this mode results in the following error message: "Command Rejected. Change Not Allowed in Active Cell Mode." Use the cell off operating mode when changing this value.
Setting	Range: RMC12 RMC64 RMC384
Query	Same as setting.
*RST Setting	RMC12
Requirements	Test Application Revision: A.01 and above Test Application Revision A.02 added RMC64 Test Application Revision A.04 added RMC384 Lab Application Revision: A.01 and above. Lab Application Revision A.02 added RMC384
Programming Example OUTPUT 714;"CALL:DPCHANNEL:TYPE RMC12" ! Selects the 12.2 RMC for the DPCH.