Only the Main Setup commands corresponding to the Phase Noise measurement class are documented here. All other commands are identical to the Setup commands for the Standard measurement class and can be accessed by clicking here or by clicking on the softtabs on the graphic below.
Click here to view links to Setup commands for all Measurement Classes.
| Main Tab Commands | |||
Softkey |
Sub-item | SCPI |
COM |
| Phase Noise Setup... | Sweep Tab | ||
|
Noise Type |
|
|
|
Sweep Type |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Carrier Frequency |
|
|
|
Enable Search |
|
|
|
|
|
|
|
Center/Span/Start/Stop |
SENSe:PN:ADJust:CONFigure:FREQuency:LIMit:CENTer / SPAN / STARt / STOP |
|
|
Threshold |
|
|
|
Search Once |
|
|
|
Enable Pulse |
|
|
|
Pulse Setup.../Pulse Period/Frequency |
|
|
|
X CORR Gain Indicator |
|
|
|
XCORR Counter |
|
|
|
Start Offset |
|
|
|
Stop Offset |
|
|
|
RBW Ratio |
|
|
|
XCORR Factor |
SENSe:PN:CORRelation:COUNt |
|
|
View Segment |
None |
|
|
|
||
|
Fast XCORR Mode |
|
|
|
|||
|
External Mixer State |
|
|
|
Always use Internal Reference |
|
|
|
RF 1/2 Input |
|
|
|
Auto Range |
|
|
|
Max Input Level |
|
|
|
Enable Attenuator Setting |
|
|
|
Attenuator |
|
|
|
External Mixer Setup |
|
|
|
Model, Band, LO Input |
None (Use the following commands for manual setup) |
|
|
LO Harmonic Number |
|
|
|
RF > LO or RF < LO |
None |
|
|
LO1/2 Output Level Enable |
|
|
|
LO1/2 Output Level Value |
|
|
|
IF Gain IF1/2 In |
None |
|
|
Residual Noise |
|
|
|
Number of DUT |
None |
|
|
Source Internal/External |
None |
|
|
Source 1/2 Out |
None |
|
|
RF 1/2 Input |
None |
|
|
Path Delay Compensation |
|
|
|
Auto or Manual |
|
|
|
Path Delay Value |
|
|
|
Measure Path Delay |
None |
|
|
Baseband |
|
|
|
Input (Block Capacitor Selection) |
|
|
|
Gain |
|
|
|
Discharge DC Block C |
|
|
|
|||
|
State |
|
|
|
Frequency |
|
|
|
Power |
|
|
|
Resolution |
|
|
|
Spurious Tab (See Sample Program) | ||
|
Show Spurious Table |
|
|
|
Table Sort Order |
|
|
|
Select Trace |
|
|
|
Enable Spur Analysis |
|
|
|
Spur Sensibility |
|
|
|
Min. Spur Level |
|
|
|
Omit Displayed Spur |
|
|
|
|||
|
Start Freq |
|
|
|
Lower Threshold |
|
|
|
Upper Threshold |
|
|
|
Add |
|
|
|
Delete |
None |
|
|
Delete All |
|
|
|
Save Table |
None |
|
|
Load Table |
|
|
|
Omit User Specified Spur |
|
|
|
|||
|
Spurious Freq |
|
|
|
Add |
|
|
|
Delete |
None |
|
|
Delete All |
|
|
|
Save Table |
None |
|
|
Load Table |
|
|
|
Integrated Noise Tab (See Sample Program) | ||
|
Show Integrated Noise Table |
|
|
|
Weighting Filter Setup... | ||
|
Frequency |
None |
|
|
Weighting Value |
None |
|
|
Add |
None |
|
|
Delete |
None |
|
|
Delete All |
None |
|
|
Save Table |
None |
|
|
Load Table |
None |
|
|
Select Trace |
|
|
|
Range | Specified in each CALC:MEAS:PN:INT:RANG[1-4]... command |
|
|
Type | CALCulate:MEASure:PN:INTegral:RANGe[1-4]:TYPE |
|
|
Start | CALCulate:MEASure:PN:INTegral:RANGe[1-4]:STARt |
|
|
Stop | CALCulate:MEASure:PN:INTegral:RANGe[1-4]:STOP |
|
|
Weighting Filter | CALCulate:MEASure:PN:INTegral:RANGe[1-4]:WEIGhting |
|
|
Spot Noise Tab (See Sample Program) | ||
|
Show Spot Noise Table | DISPlay:WINDow:TABLe:SNOise:ENABle |
|
|
Select Traces | CALCulate:MEASure:DEFine |
|
|
Define Spot Frequencies | CALCulate:MEASure:PN:SNOise:USER[1-6]:X
CALCulate:MEASure:PN:SNOise:USER[1-6][:STATe] |
|
| Decade Edges | CALCulate:MEASure:PN:SNOise:DECades[:STATe] |
|
|