CALL:HSUPa

Last updated: October 30, 2013

This section is only applicable to the lab application or feature-licensed test application.

CALL:HSUPa:BEDGain:EAGChannel:TSELection

Function	Sets/queries the `BetaEd Gain E-AGCH Table Selection` setting. This setting determines which table in the 3GPP standard 25.212 v7b0 the UE will use to interpret the absolute grant value indices signalled on E-AGCH. 0 means that UE uses Mapping of Absolute Grant Value Table 16B, whereas 1 indicates that the reference table is the Alternative Mapping of Absolute Grant Value Table 16B.1. This setting is only applicable when the CALL:HSUPa:EDCHannel:QAM16[:STATe] is set to ON. This setting can only be changed when the connection status is idle.
Setting	Range: 0 \| 1
Query	Same as setting.
*RST Setting	1
Requirements	Test Application Revision: A.17.00 and above Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:BEDGain:EAGChannel:TSELection 1" ! Sets the BetaEd Gain E-AGCH Table Selection to 1.

CALL:HSUPa:CEDChannel:TTI

Function	Sets/queries the Common E-DCH TTI Mode. This setting can only be changed when the connection status is idle.
Setting	Range: MS10\|MS2
Query	Same as setting.
*RST Setting	MS10
Requirements	Lab Application Revision: J.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:CEDChannel:TTI MS10" ! Sets the Common E-DCH TTI Mode to 10ms TTI.

CALL:HSUPa:EDCHannel:ETFCi:MSET

Function	Sets/queries the E-DCH Minimum Set E-TFCI (10ms TTI) . This setting can only be changed when the connection status is idle.
Setting	Range: 0 to 127 Resolution: 1
Query	Same as setting.
*RST Setting	9
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:EDCHannel:ETFCi:MSET 9" ! Sets the E-DCH Minimum Set E-TFCI to 9.

CALL:HSUPa:EDCHannel:ETFCi:MSET:MS2

Function	Sets/queries the E-DCH Minimum Set E-TFCI (2ms TTI) . This setting can only be changed when the connection status is idle.
Setting	Range: 0 to 127 Resolution: 1
Query	Same as setting.
*RST Setting	10
Requirements	Test Application Revision: A.13 and above Lab Application Revision: E.01 and above
Programming Example OUTPUT 714;"CALL:HSUPa:EDCHannel:ETFCi:MSET:MS2 10" ! Sets the E-DCH Minimum Set E-TFCI (2ms TTI) to 10.

CALL:HSUPa:EDCHannel:ETFCi:MSET:STATe

Function	Sets/queries the E-DCH Minimum Set E-TFCI Information State .
Setting	Range: 1\|ON\|0\|OFF
Query	Range: 1\|0
*RST Setting	1 (ON)
Requirements	Test Application Revision: A.13 and above Lab Application Revision: E.01 and above
Programming Example OUTPUT 714;"CALL:HSUPa:EDCHannel:ETFCi:MSET:STATe ON" ! Sets the E-DCH Minimum Set E-TFCI Information State to On.

CALL:HSUPa:EDCHannel:TTI

Function	Sets/queries the E-DCH TTI .
Setting	Range: MS10 (10 ms TTI)\|MS2 (2 ms TTI)
Query	Same as setting.
*RST Setting	MS10
Requirements	Test Application Revision: A.13 and above Lab Application Revision: E.01 and above
Programming Example OUTPUT 714;"CALL:HSUPa:EDCHannel:TTI MS10" ! Sets the HSUPA TTI mode to 10ms TTI.

CALL:HSUPa:EDCHannel:QAM16[:STATe]

Function	Sets/queries the `E-DCH 16QAM State` . This setting determines whether the test set signals the UE to operate in UL 16QAM mode for E-DCH. This setting is only applicable when the CALL:HSUPa:EDCHannel:TTI is set to MS10.
Setting	Range: 1\|ON\|0\|OFF
Query	1\|0
*RST Setting	0\|OFF
Requirements	Test Application Revision: A.17.00 and above, with the required feature license. Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:EDCHannel:QAM16 OFF" ! Sets the E-DCH 16QAM State to Off.

CALL:HSUPa:EDPCchannel[:DPCChannel]:POFFset

Function	Sets/queries the E-DPCCH/DPCCH Power Offset (DeltaE-DPCCH) . This setting can only be changed when the connection status is idle.
Setting	Range: 0 to 8 Resolution: 1
Query	Same as setting.
*RST Setting	0
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:EDPCchannel:POFFset 0" ! Sets E-DPCCH/DPCCH Power Offset (DeltaE-DPCCH) to 0.

CALL:HSUPa:EDPDchannel:PCFormula

Function	Sets/queries the `E-DPDCH Power Calculation Formula` setting. This setting determines what formula the UE uses to calculate the E-DPDCH power. This setting can only be changed when the connection status is idle.
Setting	Range: EXTRapolation \| INTerpolation
Query	Range: EXTR \| INT
*RST Setting	EXTRapolation
Requirements	Test Application Revision: A.17.00 and above, with the required feature license. Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:EDPDchannel:PCFormula EXTRapolation" ! Sets the E-DPDCH Power Calculation Formula to EXTRapolation.

CALL:HSUPa:ERNTi[:PRIMary]

Function	Sets/queries the Primary E-RNTI (Hex) . This setting can only be changed when the connection status is idle.
Setting	Range: 0 to FFFF (1 to 4 characters from the set 0123456789AaBbCcDdEeFf)
Query	Range: "0000" to "FFFF" (The return string is always 4 characters from the set 0123456789AaBbCcDdEeFf, enclosed by double quotes.)
*RST Setting	"AAAA"
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:ERNTi 'AAAA'" ! Sets the Primary E-RNTI (Hex) to AAAA.

CALL:HSUPa:ERNTi:ALTernate

Function	Sets/queries the Alternate E-RNTI (Hex). This setting can only be changed when the connection status is idle.
Setting	Range: 0 to FFFF (1 to 4 characters from the set 0123456789AaBbCcDdEeFf)
Query	Range: "0000" to "FFFF" (The return string is always 4 characters from the set 0123456789AaBbCcDdEeFf, enclosed by double quotes.)
*RST Setting	"5555"
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:ERNTi:ALTernate '5555'" ! Sets the Alternate E-RNTI (Hex) to 5555.

CALL:HSUPa:ETFCi:BOOSt[:VALue]

Function	Sets/queries the `E-TFCI Boost` setting. When CALL:HSUPa:ETFCi:BOOSt:INFormation[:STate] is set to On, this setting determines the E-TFCI threshold beyond which boosting of E-DPCCH is enabled. This setting can only be changed when the connection status is idle.
Setting	Range: 0 to 127
Query	Same as setting.
*RST Setting	127
Requirements	Test Application Revision: A.17.00 and above Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;" CALL:HSUPa:ETFCi:BOOSt 127" ! Sets the E-TFCI Boost to 127.

CALL:HSUPa:ETFCi:BOOSt:DT2Tp

Function	Sets/queries the `DeltaT2TP` setting. When CALL:HSUPa:ETFCi:BOOSt:INFormation[:STate] is set to On and CALL:HSUPa:ETFCi:BOOSt[:VALue] is set to a value other than 127, this setting determines the Delta T2TP value that would be signalled to the UE. The power offset values (in dB) for each signalled value are defined in 3GPP 25.213 v770 Table 1B.0. This setting can only be changed when the connection status is idle.
Setting	Range: 0 to 6
Query	Same as setting.
*RST Setting	2
Requirements	Test Application Revision: A.17.00 and above Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:ETFCi:BOOSt:DT2Tp 2" ! Sets the `DeltaT2TP` to 2.

CALL:HSUPa:ETFCi:BOOSt:INFormation[:STate]

Function	Sets/queries the `E-TFC Boost Info State` setting. This setting determines whether the test set enables the boosting of E-DPCCH. This setting can only be changed when the connection status is idle.
Setting	1\|ON\|0\|OFF
Query	1\|0
*RST Setting	0\|OFF
Requirements	Test Application Revision: A.17.00 and above Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:ETFCi:BOOSt:INFormation Off" ! Sets the E-TFC Boost Info State to Off.

CALL:HSUPa:ETFCi:POFFsets:REFerence

Function	Sets/queries the Predefined Reference E-TFCI Power Offsets .
Setting	Range: DEF3410801\|DEF3410802\|DEF3412101\|DEF3412102\|DEF3412103\|DEF3412104
Query	Same as setting.
*RST Setting	DEF3410802
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above Lab Application Revision: G.00.09 and above, added DEF3412103 Lab Application Revision: G.01.00 and above, added DEF3412104
Programming Example OUTPUT 714;"CALL:HSUPa:ETFCi:POFFsets:REFerence DEF3410802" ! Sets the Reference E-TFCI Power Offsets to match those in the Definition 34108-02.

CALL:HSUPa:ETFCi:POFFsets:REFerence:CONTrol

Function	Sets/queries the Reference E-TFCI Power Offset Control .
Setting	PDEFined \| MANual
Query	Same as setting.
*RST Setting	PDEFined
Requirements	Lab Application Revision: E.01 and above
Programming Example OUTPUT 714;"CALL:HSUPa:ETFCi:POFFsets:REFerence:CONTrol PDEFined" ! Sets the Reference E-TFC Configuration to Pre-defined.

CALL:HSUPa:ETFCi:POFFsets:REFerence:MANual:INDex

Function	Sets/queries the Reference E-TFCI. Each entry in this list defines the Reference E-TFCI as part of Reference E-TFCIs IE that is signaled to UE at call setup. Whether the Reference E-TFCI is actually present in the RRC message is controlled by the "Reference E-TFCI 1 to 8 States" setting.The valid range for each entry in this list depends on the HSUPA TTI mode and E-DCH TB size table (3GPP TS 25.321 Annex B) in use (See Table below). The default value comes from 3GPP TS 34.108 s9.2.
Setting	Range: 8 comma separated values (see table below for valid ranges)) Resolution: 1
Query	Same as setting
*RST Setting	11,0,0,0,0,0,0,0
Requirements	Lab Application Revision: E.01 and above
Programming Example OUTPUT 714;"CALL:HSUPa:ETFCi:POFFsets:REFerence:MANual:INDex 11,0,0,0,0,0,0,0" ! Sets Reference E-TFCI to 11,0,0,0,0,0,0,0.

Reference E-TFCI Valid Ranges
HSUPA TTI Mode	E-TFCI Table Index	Valid Range ofReference E-TFCI
2ms TTI	0	0 to 127
2ms TTI	1	0 to 125
10ms TTI	0	0 to 127
10ms TTI	1	0 to 120

CALL:HSUPa:ETFCi:POFFsets:REFerence:MANual:POFFset

Function	Sets/queries the Reference E-TFCI Power Offset. Each entry the in this list defines the Reference E-TFCI PO that is part of Reference E-TFCIs IE signaled to UE at call setup. Whether the Reference E-TFCI PO is actually present in the RRC message is controlled by the "Reference E-TFCI 1 to 8 States" setting.3GPP TS 25.213 Table 1B.1 defines the values for this parameter (also known as deltaE-DPDCH), which is used to determine the reference gain factor ßed,ref that is then used together with the reference E-TFCI to calculate the gain factor ßed for the selected E-TFCI based on the configured HARQ profile.The default value comes from 3GPP TS 34.108 s9.2.
Setting	Range: 8 comma separated values of 0 to 31 Resolution: 1
Query	Same as setting
*RST Setting	4,0,0,0,0,0,0,0
Requirements	Lab Application Revision: E.01 and above
Programming Example OUTPUT 714;"CALL:HSUPa:ETFCi:POFFsets:REFerence:MANual:POFFset 4,0,0,0,0,0,0,0" ! Sets Reference E-TFCI Power Offset to 4,0,0,0,0,0,0,0.

CALL:HSUPa:ETFCi:POFFsets:REFerence:MANual:STATe

Function	Sets/queries the Reference E-TFCI 1 to 8 States. A maximum of 8 reference E-TFCs can be signaled to UE according to the 3GPP specifications. So, each position in this parameter's list corresponds one of these 8 reference E-TFCs. Only those positions that are set to "1" will be present in the RRC message sent to the UE.The default value comes from 3GPP TS 34.108 s9.2.
Setting	Range: 8 comma separated states (1\|ON\|0\|OFF)
Query	Same as setting
*RST Setting	1,0,0,0,0,0,0,0
Requirements	Lab Application Revision: E.01 and above
Programming Example OUTPUT 714;"CALL:HSUPa:ETFCi:POFFsets:REFerence:MANual:STATe 1,0,0,0,0,0,0,0" ! Sets Reference E-TFCI state 1 to On, and states 2 to 8 to Off.

CALL:HSUPa:ETFCi:RECord:BEHavior

Function	Sets/queries the E-TFCI Recording Behavior. This setting determines whether all E-DPDCH subframes are recorded, or only those that pass CRC checks. This setting can only be changed when E-TFCI Recording State is idle.
Setting	Range: ALL\|GCRC (Good CRC only)
Query	Same as setting.
*RST Setting	GCRC
Requirements	Lab Application Revision: E.00.34 and above Test Application Revision: A.13 and above.
Programming Example OUTPUT 714;"CALL:HSUPa:ETFCi:RECord:BEHavior GCRC" ! Sets all E-DPDCH subframe values that pass CRC checks to be recorded.

CALL:HSUPa:ETFCi:RECord:COUNt

Function	Sets/queries the E-TFCI Rec Count . This setting can only be changed when E-TFCI Recording State is idle.
Setting	Range: 1 to 50 Resolution: 1
Query	Same as setting.
*RST Setting	15
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:ETFCi:RECord:COUNt 15" ! Sets the E-TFCI Rec Count to 15.

CALL:HSUPa:ETFCi:RECord:STARt

Function

Start Recording E-TFCI Values .

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:RECord:STARt"

CALL:HSUPa:ETFCi:RECord:STOP

Function

Stop Recording E-TFCI Values .

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:RECord:STOP" 
! Stop Recording E-TFCI Values.

CALL:HSUPa:ETFCi:TINDex

Function	Sets/queries the E-TFCI Table Index (10 ms TTI) . This setting can only be changed when the connection status is idle.
Setting	Range: 0 to 1 Resolution: 1
Query	Same as setting.
*RST Setting	0
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:ETFCi:TINDex 0" ! Sets the E-TFCI Table Index (10 ms TTI) to Table 0.

CALL:HSUPa:ETFCi:TINDex:MS2

Function	Sets/queries the E-TFCI Table Index (2ms TTI). This setting controls whether the UE is instructed to use E-DCH Transport Block Size Table 0 or Table 1 from 3GPP TS 25.321 Annex B when the HSUPA TTI Mode is set to 2ms TTI (see CALL:HSUPa:EDCHannel:TTI ). The default value is set to match the generic RB Setup message from 3GPP TS 34.108 s9.1. This setting can only be changed when the connection status is idle.
Setting	Range: 0 to 1 Resolution: 1
Query	Same as setting.
*RST Setting	0
Requirements	Test Application Revision: A.13 and above Lab Application Revision: E.01 and above
Programming Example OUTPUT 714;"CALL:HSUPa:ETFCi:TINDex:MS2 0" ! Sets the E-TFCI Table Index (2 ms TTI) to Table 0.

CALL:HSUPa:ETFCi:TINDex:MS2:QAM16

Function	Sets/queries the E-TFCI Table Index (2 ms TTI with 16QAM) (See E-TFCI Table Index (2 ms TTI) / E-TFCI Table Index (2 ms TTI with 16QAM) ). This setting controls whether the UE is instructed to use 2ms TTI E-DCH Transport Block Size Table 2 or 3 (in 3GPP TS 25.321 v7a0 Annex B) when the `E-DCH TTI` is set to `2ms` (see CALL:HSUPa:EDCHannel:TTI ). This setting can only be changed when the connection status is idle.
Setting	Range: 2 \|3
Query	Same as setting.
*RST Setting	2
Requirements	Test Application Revision: A.17.00 and above Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:ETFCi:TINDex:MS2:QAM16 2" ! Sets the E-TFCI Table Index (2 ms TTI with 16QAM) to Table 2.

CALL:HSUPa:HARQ:RETRans:MAXimum

Function	Sets/queries the HARQ Maximum Number of Retransmissions .
Setting	Range: 0 to 15 Resolution: 1
Query	Same as setting.
*RST Setting	7
Requirements	Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:HARQ:RETRans:MAXimum 7" ! Sets HARQ Number of Retransmissions.

CALL:HSUPa:HBIT:APERiod

Function	Sets/queries the Happy Bit Avg Period .
Setting	Range: 0.5 to 3600 seconds Resolution: 0.5 seconds
Query	Same as setting.
*RST Setting	1 second
Requirements	Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:HBIT:APERiod 1" ! Sets the Happy Bit Average Period to 1 seconds.

CALL:HSUPa:HBIT:DCONdition

Function	Sets/queries the Happy Bit Delay Cond .
Setting	Range: MS2 \| MS10 \| MS20 \| MS50 \| MS100 \| MS200 \| MS500 \| MS1000
Query	Same as setting.
*RST Setting	MS100
Requirements	Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:HBIT:DCONdition MS100" ! Sets the Happy Bit Delay Condition to 100 MS.

CALL:HSUPa:MS:REPorted:CEDChannel?

Function	Queries Common E-DCH.
Query	Range: True \| False
*RST Setting	False
Requirements	Lab Application Revision: J.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:MS:REPorted:CEDChannel?" ! Queries the UE reported support of Common E-DCH.

CALL:HSUPa:MS:REPorted:EDCHannel:CATegory?

Function	Queries the UE reported E-DCH Category. See Rep EDCH Cat/Ext .
Query	Range: CAT1\|CAT2\|CAT3\|CAT4\|CAT5\|CAT6\|NREP\|NSUP
*RST Setting	NREP
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:MS:REPorted:EDCHannel:CATegory?" ! Queries the UE Reported E-DCH Category.

CALL:HSUPa:MS:REPorted:EDCHannel:CATegory:EXTension?

Function	Queries the UE reported E-DCH Category Extension. See Rep EDCH Cat/Ext .
Query	CAT7 \| NREP
*RST Setting	NREP
Requirements	Test Application Revision: A.17 and above, with the required feature license Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:MS:REPorted:EDCHannel:CATegory:Extension?" ! Queries the UE Reported E-DCH Category Extension.

CALL:HSUPa:MS:REPorted:HBIT[:LAST]?

Function	Queries the Last Happy Bit .
Query	HAPP \|NHAP \|NONE
*RST Setting	NONE
Requirements	Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:MS:REPorted:HBIT?" ! Queries the Last Happy Bit.

CALL:HSUPa:MS:REPorted:HBIT:RATio?

Function	Queries the Happy Bit Ratio .
Query	Range: 0.0 to 100.0 %, 9.91E+37 Resolution: 0.1 %
*RST Setting	9.91E+37
Requirements	Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:MS:REPorted:HBIT:RATio?" ! Queries the Happy Bit Ratio.

CALL:HSUPa:MS:REPorted:IISPeed?

Function	Queries MAC-i/is.
Query	Range: True \| False
*RST Setting	False
Requirements	Lab Application Revision: J.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:MS:REPorted:IISPeed?" ! Queries the UE reported support of MAC-i/is.

CALL:HSUPa:SERVice:PSData:EDCHannel:MAC

Function	Sets/queries E-DCH MAC Entity Type.
Query	Range: EESPeed \| IISPeed
*RST Setting	EESPeed
Requirements	Lab Application Revision: J.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:PSData:EDCHannel:MAC EESPeed" ! Sets the MAC-e/es to be used as the underlying MAC layer entity when working in HSUPA PS Data mode in CELL_DCH state.

CALL:HSUPa:SERVice:PSData:EDPDchannel:CCODes:MAX

Function	Sets/queries PS Data E-DPDCH Max Channel Codes . This setting is used to control the value for the E-DPDCH Max Channelisation Codes parameter that is signaled to the UE at the setup of a PDP Context that uses 10ms TTI or 2ms TTI on the E-DCH, depending on the setting of "HSUPA TTI Mode." The default for this parameter is set to allow the maximum data throughput that is possible when using 10ms TTI. When using 2ms TTI, in order to get maximum data throughput, this parameter must be set to "2SF2+2SF4." The value "2SF2+2SF4" is only available when "UTRA FDD GPRS Service Radio Access Bearer" is set to "HSUPA UL/HSDPA DL PS" and "HSPA PS Data SRB Mapping Mode" is set to "E-DCH/DCH" or "E-DCH/HS-DSCH" , which means no uplink DPDCH is configured. If "UTRA FDD GPRS Service Radio Access Bearer" is not set to "HSUPA UL/HSDPA DL PS," this parameter is ignored. This setting can only be changed when the connection status is Idle.
Setting	Range: SF256\|SF128\|SF64\|SF32\|SF16\|SF8\|SF4 TSF4 (2sf4) TSF2 (2sf2) T2T4 (2sf2+2sf4)
Query	Same as setting.
*RST Setting	TSF2
Requirements	Lab Application Revision: U.00.13 and above Lab Application Revision: E.01 and above, added T2T4
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:PSData:EDPDchannel:CCODes:MAX TSF2" ! Sets the PS Data E-DPDCH Max Channel Codes to 2sf2.

CALL:HSUPa:SERVice:PSData:EDPDchannel:CCODes:MAXimum

Function	Sets/queries the Common E-DCH E-DPDCH Max Channelization Codes. This setting can only be changed when the connection status is Idle.
Setting	Range: SF256\|SF128\|SF64\|SF32\|SF16\|SF8\|SF4\|TSF4\|TSF2\|T2T4
Query	same with the setting
*RST Setting	TSF4
Requirements	Lab Application Revision: J.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:PSData:EDPDchannel:CCODes:MAXimum TSF4" ! Sets the Common E-DCH E-DPDCH Max Channelization Codes to 2sf4.

CALL:HSUPa:SERVice:PSData:ERGChannel:INFormation[:STATe]

Function	Sets/queries PS Data E-RGCH Information State . This setting can only be changed when the connection status is Idle.
Setting	Range: 1\|ON\|0\|OFF
Query	Range: 1\|0
*RST Setting	1 (ON)
Requirements	Lab Application Revision: U.00.13 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:PSData:ERGChannel:INFormation ON" ! Sets the RB Test Mode E-RGCH Information State to On.

CALL:HSUPa:SERVice:PSData:MACD:PDUSize

Function	Sets/queries PS Data MAC-d PDU Size when EDCH MAC Entity Type is set to MAC-e/es or mac-i/is and UL AM RLC Mode is set to fixed. This setting controls the size of the E-DCH MAC-d PDU that is to be used to configure the UE in signalling message during HSUPA PS Data call setup procedure.
Setting	Range: 336 to 5000 in increments of 8.
Query	Same as setting
*RST Setting	336
Requirements	Lab Application Revision: G.00.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:PSData:MACD:PDUSize 336" ! Sets PS Data MAC-d PDU Size to 336 Bits.

CALL:HSUPa:SERVice:PSData:RLC:UPLink:LINDicatior:SIZE

Function	Sets/queries `Flexible RLC Length Ind Size`. This setting can only be changed when the connection status is Idle.
Setting	Range: 7 \| 15
Query	Same as setting
*RST Setting	15
Requirements	Lab Application Revision: J.01.00 and above.
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:PSData:RLC:UPLink:LINDicatior:SIZE 15" ! Sets the Length Indicator size in uplink AM RLC layer to 15.

CALL:HSUPa:SERVice:PSData:RLC:UPLink:MAXimum:PDU:PSIZe

Function	Sets/queries Max Flexible AM RLC PDU Payload Size. This setting can only be changed when the connection status is Idle.
Setting	Range: 38 to 1503 Units: bytes
Query	Same as setting
*RST Setting	1503
Requirements	Lab Application Revision: J.01.00 and above.
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:PSData:RLC:UPLink:MAXimum:PDU:PSIZe 1503" ! Sets the maximum RLC PDU size in uplink AM RLC layer to 1503.

CALL:HSUPa:SERVice:PSData:RLC:UPLink:MINimum:PDU:PSIZe

Function	Sets/queries Min Flexible AM RLC PDU Payload Size. This setting can only be changed when the connection status is Idle.
Setting	Range: 38 to 1503 Units: bytes
Query	Same as setting
*RST Setting	1503
Requirements	Lab Application Revision: J.01.00 and above.
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:PSData:RLC:UPLink:MINimum:PDU:PSIZe 1503" ! Sets the minimum RLC PDU size in uplink AM RLC layer to 1503.

CALL:HSUPa:SERVice:PSData:RLC:UPLink:MODE

Function	Sets/queries UL AM RLC Mode. This setting can only be changed when the connection status is Idle.
Setting	Range: Fixed \| Flexible
Query	Same as setting
*RST Setting	Fixed
Requirements	Lab Application Revision: J.01.00 and above.
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:PSData:RLC:UPLink:MODE Flexible" ! Sets the uplink AM RLC work mode to Flexible.

CALL:HSUPa:SERVice:RBTest:EDPDchannel:CCODes:MAX

Function	Sets/queries RB E-DPDCH Max Channel Codes (12.2k + HSPA) . This setting can only be changed when the connection status is Idle.
Setting	Range: SF256\|SF128\|SF64\|SF32\|SF16\|SF8\|SF4 TSF4 (2sf4) TSF2 (2sf2)
Query	Same as setting.
*RST Setting	TSF4
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:RBTest:EDPDchannel:CCODes:MAX TSF4" ! Sets the RB Test Mode E-DPDCH Max Channel Codes to 2sf4.

CALL:HSUPa:SERVice:RBTest:EDPDchannel:CCODes:MAX:HSPA

Function	Sets/queries RB Test Mode E-DPDCH Max Channelisation Codes (HSPA Only). This setting is used to control the value for E-DPDCH Max Channelisation Codes that is signaled to the UE at the setup of an RB Test Mode call when "UTRA FDD RB Test Mode Channel Type" is set to "HSPA Only." The default value for this parameter is set to match 3GPP TS 34.108 s9.2.If "UTRA FDD RB Test Mode Channel Type" is set to"12.2k RMC+HSPA," this parameter is ignored.
Setting	Range: SF256\|SF128\|SF64\|SF32\|SF16\|SF8\|SF4 TSF4 (2sf4) TSF2 (2sf2) T2T4 (2sf2+2sf4)
Query	Same as setting.
*RST Setting	T2T4
Requirements	Test Application Revision: A.13 and above, with the required feature license Lab Application Revision: E.01 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:RBTest:EDPDchannel:CCODes:MAX:HSPA T2T4" ! Sets the RB Test Mode E-DPDCH Max Channel Codes (HSPA Only) to 2sf2+2sf4.

CALL:HSUPa:SERVice:RBTest:ERGChannel:INFormation[:STATe]

Function	Sets/queries the RB Test Mode E-RGCH Information State . This setting can only be changed when the connection status is Idle.
Setting	Range: 1\|ON\|0\|OFF
Query	Range: 1\|0
*RST Setting	0
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:RBTest:ERGChannel:INFormation OFF" ! Sets the RB Test Mode E-RGCH Information State to Off.

CALL:HSUPa:SERVice:RBTest:HARQ:RETRans:MAXimum

Function	Sets/queries the RB Test Mode E-DCH Maximum Number of HARQ Retransmissions. This setting controls the maximum number of retransmissions a HARQ process in the UE will perform for a given block of data before giving up and moving onto a new block of data under an HSUPA RB test mode call. The default value was chosen to match both 3GPP TS 34.108 s9.1 and s9.2.Note: This parameter applies to two MAC-d flows when SRBs are mapped onto E-DCH/DCH.This setting is only available in the lab application (LA). In the test application (TA) this parameter is fixed to 7.
Setting	Range: 0 to 15 Resolution: 1
Query	Same as setting
*RST Setting	7
Requirements	Lab Application Revision: E.01 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:RBTest:HARQ:RETRans:MAXimum 7" ! Sets the RB Test Mode E-DCH Maximum Number of HARQ Retransmissions to 7.

CALL:HSUPa:SERVice:RBTest:RLCPdu:SIZE

Function	Sets/queries the E-DCH RLC PDU Size.
Setting	Range: BITS336\|BITS112
Query	Same as setting.
*RST Setting	BITS336
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:RBTest:RLCPdu:SIZE BITS336" ! Sets the E-DCH RLC PDU Size to 336.

CALL:HSUPa:SERVice:RBTest:RLCSdu:SIZE

Function	Sets/queries the RB E-DPDCH Max Channel Codes (HSPA) . This setting can only be changed when the connection status is Idle.
Setting	Range: BITS2936\|BITS5872\|BITS8808\|BITS11744\|BITS14765\|BITS29360\|BITS35232
Query	Same as setting.
*RST Setting	BITS2936
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SERVice:RBTest:RLCSdu:SIZE BITS2936" ! Sets the E-DCH RLC SDU Size to 2936.

CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue[1]

Function	When the E-DCH TTI is `2 ms` , the E-DCH 16QAM State is `On` and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the `Absolute Grant Pattern - Value 1.` This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	ZGR
Requirements	Test Application Revision: A.17 and above, with the required feature license Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue ZGRant" ! Sets the Absolute Grant Pattern - Value 1 to ZERO_GRANT.

CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue2

Function	When the E-DCH TTI is `2 ms` , the E-DCH 16QAM State is `On` and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the `Absolute Grant Pattern - Value 2.` .This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Test Application Revision: A.17.00 and above, with the required feature license Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue2 ZGRant" ! Sets the Absolute Grant Pattern - Value 2 to ZERO_GRANT.

CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue3

Function	When the E-DCH TTI is `2 ms` , the E-DCH 16QAM State is `On` and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the `Absolute Grant Pattern - Value 3` . This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Test Application Revision: A.17.00 and above, with the required feature license Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue3 INDex31" ! Sets the Absolute Grant Pattern - Value 3 to 31:4(377/15)^2.

CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue4

Function	When the E-DCH TTI is `2 ms` , the E-DCH 16QAM State is `On` and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the `Absolute Grant Pattern - Value 4.` This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Test Application Revision: A.17.00 and above, with the required feature license Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue4 INDex31" ! Sets the Absolute Grant Pattern - Value 4 to 31:4(377/15)^2.

CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue5

Function	When the E-DCH TTI is `2 ms` , the E-DCH 16QAM State is `On` and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the `Absolute Grant Pattern - Value 5.` This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Test Application Revision: A.17.00 and above, with the required feature license Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue5 INDex31" ! Sets the Absolute Grant Pattern - Value 5 to 31:4(377/15)^2.

CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue6

Function	When the E-DCH TTI is `2 ms` , the E-DCH 16QAM State is `On` and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the `Absolute Grant Pattern - Value 6.` This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Test Application Revision: A.17.00 and above, with the required feature license Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue6 INDex31" ! Sets the Absolute Grant Pattern - Value 6 to 31:4(377/15)^2.

CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue7

Function	When the E-DCH TTI is `2 ms` , the E-DCH 16QAM State is `On` and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the `Absolute Grant Pattern - Value 7.` This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Test Application Revision: A.17.00 and above, with the required feature license Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue7 INDex31" ! Sets the Absolute Grant Pattern - Value 7 to 31:4(377/15)^2.

CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue8

Function	When the E-DCH TTI is `2 ms` , the E-DCH 16QAM State is `On` and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the `Absolute Grant Pattern - Value 8.` This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Test Application Revision: A.17.00 and above, with the required feature license Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue8 INDex31" ! Sets the Absolute Grant Pattern - Value 8 to 31:4(377/15)^2.

CALL:HSUPa:SGRant:ABSolute:ALTernative:SSHot[:VALue]

Function	Sets/queries the Single Shot AG .
Setting	Range: ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:SSHot INDex31" ! Sets the Single Shot Absolute Grant to 31:6(168/15)^2.

CALL:HSUPa:SGRant:ABSolute:MODE

Function	Sets/queries the AG Mode .
Setting	Range: SSHot\|PATTern
Query	Same as setting.
*RST Setting	SSH
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:MODE SSHot" ! Sets the AG Mode to Single Shot.

CALL:HSUPa:SGRant:ABSolute:PATTern:LENGth

Function	Sets/queries the Absolute Grant Pattern Length. This setting controls the number of values in a pattern on the E-AGCH that are transmitted to the UE when CALL:HSUPa:SGRant:ABSolute:MODE is set to PATTern.
Setting	Range: 2 to 8 Resolution: 1
Query	Same as setting
*RST Setting	2
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above, with the required feature license
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:LENGth 2" ! Sets the Absolute Grant Pattern Length to 2.

CALL:HSUPa:SGRant:ABSolute:PATTern:VALue[1]

Function	Sets/queries the Absolute Grant Pattern - Length . This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	ZGR
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue ZGRant" ! Sets the Absolute Grant Pattern - Value 1 to ZERO_GRANT.

CALL:HSUPa:SGRant:ABSolute:PATTern:VALue2

Function	Sets/queries the Absolute Grant Pattern - Value 2 (see Absolute Grant Pattern Values ). This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue2 INDex31" ! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

CALL:HSUPa:SGRant:ABSolute:PATTern:VALue3

Function	Sets/queries the Absolute Grant Pattern - Value 3. This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above, with the required feature license
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue3 INDex31" ! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

CALL:HSUPa:SGRant:ABSolute:PATTern:VALue4

Function	Sets/queries the Absolute Grant Pattern - Value 4. This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above, with the required feature license
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue4 INDex31" ! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

CALL:HSUPa:SGRant:ABSolute:PATTern:VALue5

Function	Sets/queries the Absolute Grant Pattern - Value 5. This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above, with the required feature license
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue5 INDex31" ! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

CALL:HSUPa:SGRant:ABSolute:PATTern:VALue6

Function	Sets/queries the Absolute Grant Pattern - Value 6. This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above, with the required feature license
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue6 INDex31" ! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

CALL:HSUPa:SGRant:ABSolute:PATTern:VALue7

Function	Sets/queries the Absolute Grant Pattern - Value 7. This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above, with the required feature license
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue7 INDex31" ! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

CALL:HSUPa:SGRant:ABSolute:PATTern:VALue8

Function	Sets/queries the Absolute Grant Pattern - Value 8. This setting cannot be changed when `AG Mode` is set to `Pattern` .
Setting	Range: DTXA[1]\|ZGRant\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Lab Application Revision: F.00 and above Test Application Revision: A.14 and above, with the required feature license
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue8 INDex31" ! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

CALL:HSUPa:SGRant:ABSolute:RBSetup[:VALue][:DCH]

Function	Sets/queries the RB Setup AG . This setting can only be changed when the connection status is idle.
Setting	Range: ZGRant\|INDex0\|INDex1\|INDex2\|INDex3...\|INDex37\|INDex38
Query	Same as setting.
*RST Setting	IND37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above Lab Application Revision: G.01 and above: Added INDex38
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:RBSetup INDex37" ! Sets the RB Setup Absolute Grant to 37:6(168/15)^2.

CALL:HSUPa:SGRant:ABSolute:RBSetup[:VALue]:FACH

Function	Sets/queries the Common E-DCH RB Setup AG. This setting can only be changed when the connection status is idle.
Setting	Range: ZGRant\|INDex0\|INDex1\|INDex2\|INDex3...\|INDex37\|INDex38
Query	Same as setting.
*RST Setting	IND37
Requirements	Lab Application Revision: J.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:RBSetup:FACH INDex37" ! Sets the Initial Serving Grant to 37:6(168/15)^2.

CALL:HSUPa:SGRant:ABSolute:RBSetup:QAM16[:VALue]

Function	Sets/queries the RB Setuo AG (16QAM). This set of values is used when the E-DCH TTI is `2 ms` and the E-DCH 16QAM State is set to `On` . This setting can only be changed when the connection status is idle.
Setting	Range: ZGRant\|INDex0\|INDex1\|INDex2\|INDex3...\|INDex38
Query	Same as setting.
*RST Setting	IND37
Requirements	Test Application Revision: A.17.00 and above Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:RBSetup:QAM16 INDex37" ! Sets the RB Setup Absolute Grant (16QAM)to 37:4(377/15)^2.

CALL:HSUPa:SGRant:ABSolute:SSHot[:VALue]

Function	Sets/queries the Single Shot AG .
Setting	Range: ZGRant\|INACtive\|INDex2\|INDex3...\|INDex31
Query	Same as setting.
*RST Setting	IND31
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above Lab Application Revision: J.01.00 and above, added INACtive.
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:SSHot INDex31" ! Sets the Single Shot Absolute Grant to 31:6(168/15)^2.

CALL:HSUPa:SGRant:ABSolute:SSHot:SEND[:IMMediate]

Function

Initiates the Send Single Shot AG action.

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:SSHot:SEND" 
! Send Single Shot AG.

CALL:HSUPa:SGRant:RELative:DOWN:SEND[:IMMediate]

Function

Initiates the Send Relative Grant Down action.

This action is rejected if RB Test Mode E-RGCH Information State is Off . A warning is posted if you initiate this action when HSPA Cell 1 Connected E-RGCH Level is Off .

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:RELative:DOWN:SEND" 
! Send Relative Grant Down

CALL:HSUPa:SGRant:RELative:MODE

Function	Sets/queries the RG Mode .
Setting	Range: Single\|Continuous
Query	Same as setting.
*RST Setting	Single
Requirements	Lab Application Revision: G.00.00 and above Lab Application Revision: I.00.00 and above, changed the range from SSHot\|PATTern to Single\|Continuous
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:RELative:MODE Single" ! Sets the RG Mode to Single Shot.

CALL:HSUPa:SGRant:RELative:PATTern

Function	Sets/queries the Relative Grant Pattern.
Setting	Range: HOLD\|UP\|DOWN\|D12Hold8 \| D4Hold8\|MANual
Query	Same as setting.
*RST Setting	HOLD
Requirements	Lab Application Revision: G.00.00 and above Lab Application Revision: G.01.00: Added D12H8 Lab Application Revision H.01.00: Added D4Hold8 Lab Application Revision I.00.00: Added MANual
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:RELative:PATTern HOLD" ! Sets the RG Pattern to All Holds.

CALL:HSUPa:SGRant:RELative:PATTern:MANual

Function	Sets/queries the sequence of relative grant pattern transmitted on E-RGCH. This setting is applicable when RG Mode is set to `Pattern` and RG Pattern is set to `Manual` . Changing the setting when RG Mode is set to Pattern will post +530 error message: "FDD call processing error; Relative grant pattern values cannot be changed while the relative grant mode is set to pattern." Before changing the setting, you need to set RG Mode to Single Shot.
Setting	Range: {1-2}, {HOLD\|UP\|DOWN}, {1-256}, {HOLD\|UP\|DOWN}, {1-256} Description: {E-RGCH Pattern Number of Segments}, {E-RGCH Pattern First Segment Command Type}, {E-RGCH Pattern First Segment Length}, {E-RGCH Pattern Second Segment Command Type}, {E-RGCH Pattern Second Segment Length}
Query	Same as setting.
*RST Setting	2, DOWN, 12, HOLD, 8
Requirements	Lab Application Revision I.00.00:
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:RELative:PATTern:MANual 2,DOWN,12,HOLD,8" ! Sets the sequence of RG Pattern to 2,DOWN,12,HOLD,8.

CALL:HSUPa:SGRant:RELative:PATTern:PERiodic[:STATe]

Function	Sets/queries the E-RGCH Pattern Periodic Transmission State. If set to `On` , the test set transmits a periodic sequence of values to the UE over the E-RGCH immediately. If set to `Off` , when an CALL:HSUPa:SGRant:RELative:PATTern:SEND[:IMMediate] action is performed, the test set transmits a sequence of values to the UE over the E-RGCH only once. The values that are transmitted to the UE are defined by RG Pattern This setting is only applicable when the RG Mode is set to `Pattern` and the RG Pattern is set to `12 Downs + 8 Holds` . This setting can not be changed while the RG Mode is set to `Pattern` . This setting is GPIB only.
Setting	Range: 1\|On\|0\|Off
Query	Range: 1\|0
*RST Setting	1 (On)
Requirements	Test Application Revision: A.17.00 and above Lab Application Revision: G.01.00 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SGRant:RELative:PATTern:PERiodic On" ! Sets the RG Pattern Periodic Transmission State to On.

CALL:HSUPa:SGRant:RELative:PATTern:SEND[:IMMediate]

Function

Transmit a finite sequence of values to the UE over the E-RGCH. The values that are transmitted to the UE are defined by RG Pattern .

This setting is only applicable when the RG Mode is set to Pattern , the RG Pattern is set to 12 Downs + 8 Holds and the CALL:HSUPa:SGRant:RELative:PATTern:PERiodic[:STATe] is set to Off.

This setting is only applicable when the E-DCH is active.

Requirements

Test Application Revision: A.17.00 and above
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:RELative:PATTern:SEND"

CALL:HSUPa:SGRant:RELative:QUEued:CLEar

Function

Initiates the Clear Queued Relative Grants action.

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:RELative:QUEued:CLEar" 
! Clear Queued Relative Grants.

CALL:HSUPa:SGRant:RELative:UP:SEND[:IMMediate]

Function

Initiates the Send Relative Grant Up action.

This action is rejected if RB Test Mode E-RGCH Information State is Off . A warning is posted if you initiate this action when HSPA Cell 1 Connected E-RGCH Level is Off .

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:RELative:UP:SEND" 
! Send Relative Grant Up.

CALL:HSUPa:SIPeriod:GRANt

Function	Sets/queries the Scheduling Information Periodicity (Grant) .
Setting	Range: NREPort \| EETTi\|MS4 \| MS10 \| MS20 \| MS50 \| MS100 \| MS200 \| MS500 \| MS1000
Query	Same as setting.
*RST Setting	NREPort
Requirements	Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SIPeriod:GRANt NREPort" ! Sets the Scheduling Information Periodicity (Grant) to NREPort.

CALL:HSUPa:SIPeriod:NGRant

Function	Sets/queries the Scheduling Information Periodicity (No Grant) .
Setting	Range: NREPort \| EETTi\|MS4 \| MS10 \| MS20 \| MS50 \| MS100 \| MS200 \| MS500 \| MS1000
Query	Same as setting.
*RST Setting	NREPort
Requirements	Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:HSUPa:SIPeriod:NGRant NREPort" ! Sets the Scheduling Information Periodicity (No Grant) to NREPort.