• FCA (OptS9x082AS9x083A/B): Configure | Calibrate | Embedded LO | Segment Sweep

• Noise Figure App (Opt 028, 029, S93029A/B): Setup | Cal | SNP | ENR files  | NFX

• GCA (Opt S9x086A): Setup | Cal | Analysis | GCX

• Diff IQ (Opt S9x089A/B): Meas | Setup | Range Settings | Parameters | X-Axis

• SA (Opt S9x090xA): SA Setup | Source: Setup | Coherence |Advanced Settings | IF Setup |Trig. & Pulse Setup | Processing Setup | ADC & LO Setup | Data | SA Markers | IQMod

• Common Mixer Setup commands

• Frequency Offset (Opt S9x080A)

• Enhanced Time Domain Analysis [GUI Command Finder] (TDR, Option S9x011A/B)

• Modulation Distortion (Opt S9x070xB)

Description

FCA Configure Measurements

• Use Mixer commands to setup the mixer.

• Use FCA Segment commands to setup segment sweep.

• Use the following commands to setup and calibrate SMC and VMC measurements.

Create an FCA measurement

CALCulate:MEASure:DEFine

Change an FCA measurement

CALCulate:MEASure:PARameter

Sweep type

SENSe:SWEep:TYPE

Map DUT ports to PNA ports

SENSe:MIXer:PMAP

Read Input port map

SENSe:MIXer:PMAP:INPut

Read Output port map

SENSe:MIXer:PMAP:OUTPut

Avoid Spurs

SENSe:MIXer:AVOidspurs

Minimum required FCA (SMC and VMC) Cal commands

SCPI and COM examples.

Create Cal object

None

Begin Cal

SENSe:CORRection:COLLect:GUIDed:INITiate

Set connector type for each port

SENSe:CORRection:COLLect:GUIDed:CONNector:PORT:SELect

Set Cal Kit for each port

SENSe:CORRection:COLLect:GUIDed:CKIT:PORT:SELect

Returns the number of steps required by the Calibration

SENSe:CORRection:COLLect:GUIDed:STEPs?

Returns the step description.

SENSe:CORRection:COLLect:GUIDed:DESCription?

Measure a standard

SENSe:CORRection:COLLect:GUIDed:ACQuire

Generate Error Terms

SENSe:CORRection:COLLect:GUIDed:SAVE

Optional FCA (SMC and VMC) commands

See SMC and VMC specific optional commands

Set THRU method

SENSe:CORRection:COLLect:GUIDed:PATH:TMEThod

Sets ECAL auto-orientation ON or OFF

SENSe:CORRection:PREFerence:ECAL:ORIentation

Sets ECAL port map when orientation is off.

SENSe:CORRection:PREFerence:ECAL:PMAP

Perform or Omit Isolation

SENSe:CORRection:COLLect:GUIDed:ISOLation

SMC Optional commands

SMC network embed/deembed

SENSe:CORRection:COLLect:GUIDed:SMC:FSIMulator:NETWork:MODE

SMC filename

SENSe:CORRection:COLLect:GUIDed:SMC:FSIMulator:NETWork:FILename

Import existing Phase Ref Cal or Source Power Cal

SENSe:CORRection:COLLect:GUIDed:SMC:IMPort

Use Thru or perform separate power cals

SENSe:CORRection:COLLect:GUIDed:SMC:PWRCal:SEParate

Include Reverse SC12 sweep

SENSe:MIXer:REVerse

Include input/output match correction

CALCulate:MEASure:CORRection:TYPE

Use Nominal Incident Power

SENSe:MIXer:INPut:POWer:USENominal

Enable LO Power Cal

SENSe:CORRection:COLLect:GUIDed:SMC:LO:PCAL

Save to s2p and s2px file

MMEMory:STORe

Load Power Table (used with mmWave)

SENSe:CORRection:COLLect:GUIDed:PSENsor:POWTable

SMC Include Phase

Enable Phase

SENSe:MIXer:PHASe

Enable Absolute Phase

SENSe:MIXer:PHASe:ABSolute[:STATe]

Set normalize point

SENSe:MIXer:NORMalize:POINt

Choose known delay or S2P

SENSe:CORRection:COLLect:GUIDed:SMC:PHASe:METHod

Set known delay

SENSe:CORRection:COLLect:GUIDed:SMC:PHASe:DELay

Set Cal Mixer Char S2P filename

SENSe:CORRection:COLLect:GUIDed:SMC:PHASe:MIXer

Use Phase Ref Cal Set

SENSe:CORRection:COLLect:GUIDed:SMC:IMPort

Perform SMC Phase Reference Cal

Reset

SYSTem:CALibrate:PHASe:RESet

Start Freq

SYSTem:CALibrate:PHASe:FREQuency:STARt

Stop Freq

SYSTem:CALibrate:PHASe:FREQuency:STOP

Read channel number

SYSTem:CALibrate:PHASe:GUIDed:CHANnel?

Read all Phase Reference IDs

SYSTem:CALibrate:PHASe:REFerence:CATalog?

Set Phase Reference

SYSTem:CALibrate:PHASe:REFerence

Set Source Attenuator

SYSTem:CALibrate:PHASe:POWer:ATTenuator

Set Cal Set name

None

Perform Cal

Guided Cal commands

Use Phase Ref Cal Set

SENSe:CORRection:COLLect:GUIDed:SMC:IMPort

Unknown Mixer calibration state

SYSTem:CALibrate:PHASe:UNKNown:INCLude

Unknown mixer LO frequency

SYSTem:CALibrate:PHASe:UNKNown:LO:FREQuency

Unknown mixer LO power

SYSTem:CALibrate:PHASe:UNKNown:LO:POWer

Input power level to the unknown mixer

SYSTem:CALibrate:PHASe:UNKNown:INPut:POWer

Connector type and gender of your Cal Kit.

SYSTem:CALibrate:PHASe:CONNector

Cal Kit to be used to perform the S-parameter Cal

SYSTem:CALibrate:PHASe:CKIT

Set the ports to be calibrated.

SYSTem:CALibrate:PHASe:PORT[X]

Reverse Port2 Coupler

SYSTem:CALibrate:PHASe:DEEMbed

VMC Optional commands

VMC network embed/deembed

SENSe:CORRection:COLLect:GUIDed:VMC:FSIMulator:NETWork:MODE

VMC filename

SENSe:CORRection:COLLect:GUIDed:VMC:FSIMulator:NETWork:FILename

Enable LO Power Cal

SENSe:CORRection:COLLect:GUIDed:VMC:LO<n>:PCAL

FCA Segment Sweep

SCPI examples.

Recalculate

SENSe:MIXer:RECalculate

Segment Calculate

SENSe:MIXer:SEGMent:CALCulate

Query Count

SENSe:MIXer:SEGMent:COUNt?

Add Segments

SENSe:MIXer:SEGMent:ADD

Delete Segments

SENSe:MIXer:SEGMent:DEL

Remove All Segments

SENSe:MIXer:SEGMent:DELete:ALL

State

SENSe:MIXer:SEGMent[:STATe]

Number Of Points

SENSe:MIXer:SEGMent:POINts

IFBW

SENSe:MIXer:SEGMent:BWIDth

Input Fixed Freq

SENSe:MIXer:SEGMent:INPut:FREQuency:FIXed

Input Start Freq

SENSe:MIXer:SEGMent:INP:FREQuency:STARt

Input Stop Freq

SENSe:MIXer:SEGMent:INP:FREQuency:STOP

Input Fixed/Swept

SENSe:MIXer:SEGMent:INP:FREQuency:MODE

Input Power

SENSe:MIXer:SEGMent:INPut:POWer

Output Fixed Freq

SENSe:MIXer:SEGMent:OUTP:FREQuency:FIXed

Output Start Freq

SENSe:MIXer:SEGMent:OUTP:FREQuency:STARt

Output Stop Freq

SENSe:MIXer:SEGMent:OUTP:FREQuency:STOP

Output Fixed/Swept

SENSe:MIXer:SEGMent:OUTP:FREQuency:MODE

Output (+/-)

SENSe:MIXer:SEGMent:OUTP:FREQuency:SIDeband

Output Power

SENSe:MIXer:SEGMent:OUTPut:POWer

LO Fixed Freq

SENSe:MIXer:SEGMent:LO<x>:FREQuency:FIXed

LO Start Freq

SENSe:MIXer:SEGMent:LO<x>:FREQuency:STARt

LO Stop Freq

SENSe:MIXer:SEGMent:LO<x>:FREQuency:STOP

LO Fixed/Swept

SENSe:MIXer:SEGMent:LO<x>:FREQuency:MODE

Input >LO

SENSe:MIXer:SEGMent:LO<x>:FREQuency:ILTI

LO Power

SENSe:MIXer:SEGMent:LO<x>:POWer

IF (+/-)

SENSe:MIXer:SEGMent:IF:FREQuency:SIDeband

Embedded LO (used with FCA, NFX, GCX, MODX, and Swept IMDx)

Embedded LO ON | OFF

SENSe:MIXer:ELO:STATe

Select  tuning point

SENSe:MIXer:ELO:NORMalize:POINt

Set tuning mode

SENSe:MIXer:ELO:TUNing:MODE

Set broadband sweep span

SENSe:MIXer:ELO:TUNing:SPAN

Set precise tuning  tolerance

SENSe:MIXer:ELO:TUNing:TOLerance

Set precise tuning iterations

SENSe:MIXer:ELO:TUNing:ITERations

LO delta frequency

SENSe:MIXer:ELO:LO:DELTA

Resets tuning parameters

SENSe:MIXer:ELO:TUNing:RESet

Reset LO Delta frequency

SENSe:MIXer:ELO:LO:RESET

Resets the LO Frequency Delta and Tuning parameters to their default settings.

SENSe:MIXer:ELO:RESET

Sets and returns the Noise Bandwidth for Broadband and Precise tuning sweeps.

SENSe:MIXer:ELO:TUNing:NBW

Embedded LO Diagnostics (Available with Swept IMDx using COM ONLY)

Clear current diagnostic information

SENSe:MIXer:ELO:DIAGnostic:CLEAr

Get result of the last tuning sweeps.

SENSe:MIXer:ELO:DIAGnostic:STATus?

Get number of tuning sweeps.

SENSe:MIXer:ELO:DIAGnostic:SWEep:COUNt?

Was a marker was used for a tuning sweep?

SENSe:MIXer:ELO:DIAGnostic:SWEep:MARKer:STATe?

Get the marker X-axis position.

SENSe:MIXer:ELO:DIAGnostic:SWEep:MARKer:POSition?

Get the marker annotation.

SENSe:MIXer:ELO:DIAGnostic:SWEep:MARKer:ANNotation?

Get the tuning sweep X axis annotation.

SENSe:MIXer:ELO:DIAGnostic:SWEep:X:ANNotation?

Get the tuning sweep Y axis annotation.

SENSe:MIXer:ELO:DIAGnostic:SWEep:Y:ANNotation?

Get the Start sweep value.

SENSe:MIXer:ELO:DIAGnostic:SWEep:X:STARt?

Get the Stop sweep value.

SENSe:MIXer:ELO:DIAGnostic:SWEep:X:STOP?

Returns the tuning sweep parameter name.

SENSe:MIXer:ELO:DIAGnostic:SWEep:PARameter?

Returns the tuning sweep title.

SENSe:MIXer:ELO:DIAGnostic:SWEep:TITLe?

Returns the LO frequency delta from this tuning sweep

SENSe:MIXer:ELO:DIAGnostic:SWEep:LO:DELTa?

Gain Compression Setup

Create a GCA Meas

CALCulate:MEASure:DEFine

Change a GCA Parameter

CALCulate:MEASure:PARameter

Sweep Type

SENSe:SWEep:TYPE

Number of frequency points

SENSe:GCSetup:SWEep:FREQuency:POINts

Number of power points

SENSe:GCSetup:SWEep:POWer:POINts

Maximum number of points

None

Total number of points

None

Acquisition mode

SENSe:GCSetup:AMODe

Smart tolerance

SENSe:GCSetup:SMARt:TOLerance

Smart Iterations

SENSe:GCSetup:SMARt:MITerations

Smart settling time

SENSe:GCSetup:SMARt:STIMe

Smart show iterations

SENSe:GCSetup:SMARt:SITerations

Read DC at compression point

SENSe:GCSetup:SMARt:CDC

Read compression failures

SENSe:GCSetup:SFAilures?

Write port map

SENSe:GCSetup:PMAP

Read Port Map (Input)

SENSe:GCSetup:PMAP:INPut

Read Port Map (Output)

SENSe:GCSetup:PMAP:OUTPut

Remaps the source port to Port 1.

SENSe:GCSetup:PMAP:SOURce:OVERride

End of Sweep

SENSe:GCSetup:EOSoperation

Linear input power

SENSe:GCSetup:POWer:LINear:INPut:LEVel

Reverse Power

SENSe:GCSetup:POWer:REVerse:LEVel

Start power

SENSe:GCSetup:POWer:STARt:LEVel

Stop power

SENSe:GCSetup:POWer:STOP:LEVel

Compression algorithm

SENSe:GCSetup:COMPression:ALGorithm

Compression Level

SENSe:GCSetup:COMPression:LEVel

Backoff Level

SENSe:GCSetup:COMPression:BACK:LEVel

X Delta

SENSe:GCSetup:COMPression:DELTa:X

Y Delta

SENSe:GCSetup:COMPression:DELTa:Y

Saturation level

SENSe:GCSetup:COMPression:SATuration:LEVel

Interpolation

SENSe:GCSetup:COMPression:INTerpolate[:STATe]

Set and read the desired phase to measure compression.

SENSe:GCSetup:COMPression:PHASe:LEVel

Set and read compression format to be either magnitude, phase, or magnitude and phase.

SENSe:GCSetup:COMPression:PHASe:MODE

Safe Sweep enable

SENSe:GCSetup:SAFE:ENABle

Safe Sweep coarse

SENSe:GCSetup:SAFE:CPADjustment

Safe Sweep fine

SENSe:GCSetup:SAFE:FPADjustment

Safe Sweep threshold

SENSe:GCSetup:SAFE:FTHReshold

Safe Sweep max power

SENSe:GCSetup:SAFE:MLIMit

Set and read the name of the external DC device.

SENSe:GCSetup:SAFE:DC:PARameter

Set and read the maximum limit of the external DC device.

SENSe:GCSetup:SAFE:DC:MLimit

Set and read the DC readings at the compression point in the last iteration of a smart sweep

SENSe:GCSetup:SMARt:CDC

GCA/GCX Phase Commands

Set and read the state of the mixer reference.

SENSe:GCSetup:MIXer:REFerence

Set and read the aperture to use when computing the linear input power.

SENSe:GCSetup:POWer:LINear:INPut:COMPute:APERture

Set and read the state of the power smoothing.

SENSe:GCSetup:SWEep:POWer:SMOoth

Set and read the power smoothing aperture in percent.

SENSe:GCSetup:SWEep:POWer:SMOoth:APERture

Read GCA Data

Read all GCA data

CALCulate:MEASure:GCData:DATA?

Read real GCA data

CALCulate:MEASure:GCData:REAL?

Read imaginary GCA data

CALCulate:MEASure:GCData:IMAG?

Read number of iterations

CALCulate:MEASure:GCD:ITERations?

Gain Compression Analysis

Enable a compression analysis trace

CALCulate:MEASure:GCMeas:ANALysis:ENABle

Set CW frequency

CALCulate:MEASure:GCMeas:ANALysis:CWFRequency

Set to discrete or interpolated CW frequencies

CALCulate:MEASure:GCMeas:ANALysis:DISCrete

Sets X-axis display

CALCulate:MEASure:GCMeas:ANALysis:XAXis

GCA Cal

Read about GCA Cal

Gain Compression Cal

Set power for source power cal

SENSe:CORRection:GCSetup:POWer

Set connector type for power sensor.

SENSe:CORRection:GCSetup:SENSor:CONNector

Set cal kit for power sensor connector.

SENSe:CORRection:GCSetup:SENSor:CKIT

Guided Cal commands

SENSe:CORRection:COLLect:GUIDed

Noise Figure Setup

Create Noise Figure meas

CALCulate:CUSTom:DEFine

Change Noise Figure meas

CALCulate:CUSTom:MODify

Sets the number of impedance states to use

 SENSe:NOISe:IMPedance:COUNt

Select Noise Receiver

SENSe:NOISe:RECeiver

Noise averaging ON and OFF

 SENSe:NOISe:AVERage:STATe

Set averaging of noise receiver.

 SENSe:NOISe:AVERage

Set narrowband state

SENSe:NOISe:NARRowband

Set bandwidth of noise receiver.

 SENSe:NOISe:BWIDth

Set gain state of noise receiver.

 SENSe:NOISe:GAIN

Sets the port identifier of the ECal noise tuner that is connected to the PNA Source.

 SENSe:NOISe:TUNer:INPut

Sets the port identifier of the ECal noise tuner that is connected to the DUT.

 SENSe:NOISe:TUNer:OUTPut

Set and read a custom noise tuner file to be used instead of the one generated automatically based on the state.

SENSe:NOISe:TUNer:FILE:NAME

Sets the state of the custom noise tuner file.

SENSe:NOISe:TUNer:FILE[:STATe]

Set the excess noise source ON or OFF.

 CONTrol:NOISe:SOURce or

 OUTPut:MANual:NOISe[:STATe]

Set mechanical switches

SENSe:PATH:CONFig:ELEMent

Port Mapping - Noise Figure Opt 028

Write port mapping

SENSe:NOISe:PMAP

Read input port mapping

SENSe:NOISe:PMAP:INPut?

Read output port mapping

SENSe:NOISe:PMAP:OUTPut?

Noise Figure Cal - all other cal settings use standard commands.

Create Noise Cal object

N/A

Set Noise Calibration method

 SENSe:NOISe:CALibration:METHod

Set Noise Tuner identifier

SENSe:NOISe:TUNer:ID

Set Noise Recvr Method

SENSe:NOISe:CALibration:RMEThod

Noise source ENR filename

 SENSe:NOISe:ENR:FILename

Set noise source Cal Kit type

 SENSe:NOISe:SOURce:CKIT

Set ambient temperature

 SENSe:NOISe:TEMPerature:AMBient

Enables/disables the use of 302K as the ambient temperature.

SENSe:NOISe:TEMPerature:AMBient:AUTO

Sets the temperature at which the current noise measurement is occurring.

SENSe:NOISe:TEMPerature:SOURce[:VALue]

Enables/disables the use of 302K as the source temperature.

SENSe:NOISe:TEMPerature:SOURce:AUTO

Sets noise source connector type

 SENSe:NOISe:SOURce:CONNector

Set noise source connector temp

SENSe:CORRection:TCOLd:USER:VALue

Get/Save Noise Parameters SNP Data

Read noise parameter SNP data

SENSe:NOISe:SNP?

Write noise parameters to SNP file

SENSe:NOISe:SNP:SAVE

Set and read the state of the thru adapter de-embedding.

SENSe:CORRection:COLLect:NOISe:THRU:ADAPter:DEEMbed[:STATe]

Noise Figure ENR File Data Management

Set ENR calibration data.

SENSe:CORRection:ENR:CALibration:TABLe:DATA

PutENRData

Read ENR calibration data.

SENSe:CORRection:ENR:CALibration:TABLe:DATA?

GetENRData

Get/set ID of ENR table.

SENSe:CORRection:ENR:CALibration:TABLe:ID:DATA

ENRID

Get/set serial number of noise source.

SENSe:CORRection:ENR:CALibration:TABLe:SERial:DATA

ENRSN

Load ENR table from file.

MMEMory:LOAD:ENR

LoadENRFile

Save ENR table to file.

MMEMory:STORe:ENR

SaveENRFile

Create/Change DIQ Measurement

CALCulate:CUSTom:DEFine

CALCulate:CUSTom:MODify

Diff IQ Setup Dialog

SENSe:DIQ:FREQuency:RANGe:ADD

SENSe:DIQ:FREQuency:RANGe:DELete

DIQ Range Settings Dialog

Frequency

SENSe:DIQ:FREQuency:RANGe:STARt

SENSe:DIQ:FREQuency:RANGe:STOP

SENSe:DIQ:FREQuency:RANGe:IFBW

Coupling

SENSe:DIQ:FREQuency:RANGe:COUPle:STATe

SENSe:DIQ:FREQuency:RANGe:COUPle:ID

SENSe:DIQ:FREQuency:RANGe:COUPle:OFFSet

SENSe:DIQ:FREQuency:RANGe:COUPle:UCONvert

SENSe:DIQ:FREQuency:RANGe:COUPle:MULTiplier

SENSe:DIQ:FREQuency:RANGe:COUPle:DIvisor

DIQ Source Configuration Dialog

SENSe:DIQ:PORT:STATe

SENSe:DIQ:PORT:RANGe

SOURce:PHASe:EXTernal:CATalog?

SOURce:PHASe:EXTernal:PORT

Power

SENSe:DIQ:PORT:POWer:SWEep

SENSe:DIQ:PORT:POWer:STARt

SENSe:DIQ:PORT:POWer:STOP

SENSe:DIQ:PORT:POWer:ALC:MODE

SENSe:DIQ:PORT:POWer:ATTenuation

SENSe:DIQ:PORT:POWer:ATTenuation:AUTO

Phase

SENSe:DIQ:PORT:PHASe:STATe

SENSe:DIQ:PORT:PHASe:SWEep

SENSe:DIQ:PORT:PHASe:STARt

SENSe:DIQ:PORT:PHASe:STOP

SENSe:DIQ:PORT:PHASe:REFerence

SENSe:DIQ:PORT:PHASe:PARameter

SOURce:PHASe:CONTrol:TOLerance

SOURce:PHASe:CONTrol:ITERation

Match Correction

SENSe:DIQ:PORT:MATCh:STATe

SENSe:DIQ:PORT:MATCh:TRECeiver

SENSe:DIQ:PORT:MATCh:RRECeiver

SENSe:DIQ:PORT:MATCh:RANGe

DIQ Edit Parameters Dialog

SENSe:DIQ:PARameter:DEFine

SENSe:DIQ:PARameter:DELete

SENSe:DIQ: PARameter:CATalog?

DIQ Select X-Axis Dialog

CALCulate:X:AXIS:DOMain

CALCulate:X:AXIS

Mixer Setup commands

Used for FCA, Swept IMDx, IMx Spectrum, NFx, and GCx applications.

See the Mixer / Converter Setup topic

Create or Change a Custom (Application) Measurement

Create a custom measurement

CALCulate:CUSTom:DEFine

Change a custom measurement

CALCulate:CUSTom:MODify

Return handle to a converter object

None

Mixer Bottom Buttons and X-Axis display

Load a mixer setup

SENSe:MIXer:LOAD

Save a mixer setup

SENSe:MIXer:SAVE

Apply mixer settings

SENSe:MIXer:APPLy

Discard Changes

SENSe:MIXer:DISCard

X-axis display

CALCulate:MEASure:MIXer:XAXis

Mixer Frequency Tab

Calculate Input and Output frequencies

SENSe:MIXer:CALCulate

Input to swept or fixed

SENSe:MIXer:INPut:FREQuency:MODE

Input start frequency

SENSe:MIXer:INPut:FREQuency:STAR

Input stop frequency

SENSe:MIXer:INPut:FREQuency:STOP

Input power level

SENSe:MIXer:INPut:POWer

Input fixed frequency

SENSe:MIXer:INPut:FREQuency:FIXed

Set LO

LO freq fixed or swept

SENSe:MIXer:LO:FREQuency:MODE

LO fixed frequency

SENSe:MIXer:LO:FREQuency:FIXed

LO start frequency

SENSe:MIXer:LO:FREQuency:STARt

LO stop frequency

SENSe:MIXer:LO:FREQuency:STOP

Input Greater / Less that LO

SENSe:MIXer:LO:FREQuency:ILTI

Set IF

Sideband (high or low)

SENSe:MIXer:IF:FREQuency:SIDE

IF start frequency

SENSe:MIXer:IF:FREQuency:STARt

IF stop frequency

SENSe:MIXer:IF:FREQuency:STOP

Set Output

Sideband (high or low)

SENSe:MIXer:OUTPut:FREQuency:SIDE

Output start frequency

SENSe:MIXer:OUTPut:FREQuency:STARt

Output stop frequency

SENSe:MIXer:OUTPut:FREQuency:STOP00000000

Output to swept or fixed

SENSe:MIXer:OUTPut:FREQuency:MODE

Output fixed frequency

SENSe:MIXer:OUTPut:FREQuency:FIXed

Mixer (LO)Power tab

LO power

SENSe:MIXer:LO:POW

LO power start

SENSe:MIXer:LO:POW:STARt

LO power stop

SENSe:MIXer:LO:POW:STOP

Source Attenuator

SOURce:POWer:ATTenuation

Receiver Attenuator

SENSe:POWer:ATTenuator

Leveling Mode

Mixer Setup tab

Number of LOs (1 or 2)

SENSe:MIXer:STAGe

Recall a previously-configured external source.

SENSe:MIXer:LO:NAME

Assign a source to mixer input or LO.

SENSe:MIXer:ROLE:DEVice

Read all assigned roles

SENSe:MIXer:ROLE:CATalog?

Read the source assigned to a role.

SENSe:MIXer:ROLE:DEVice

Input Numerator Frac.Mult

SENSe:MIXer:INPut:FREQuency:NUMerator

Input Denominator Frac.Mult

SENSe:MIXer:INPut:FREQuency:DENominator

LO Numerator Frac. Mult.

SENSe:MIXer:LO:FREQuency:NUMerator

LO Denominator Frac.Mult

SENSe:MIXer:LO:FREQuency:DENominator

Enhanced Time Domain Analysis (TDR)

Setup and execution of TDR measurement Commands

Sets the type of parameter and format allocation for each trace.

CALCulate:TDR:ALLocate

Sets the DUT topology.

CALCulate:TDR:DEVice

Sets the emphasis post1 level.

CALCulate:TDR:EMPHasis:CURSor:POST1

Sets the emphasis post2 level.

CALCulate:TDR:EMPHasis:CURSor:POST2

Sets the emphasis pre1 level.

CALCulate:TDR:EMPHasis:CURSor:PRE1

Turns the emphasis function state ON or OFF.

CALCulate:TDR:EMPHasis:STATe

Sets the equalization CTLE DC gain parameter.

CALCulate:TDR:EQUalization:CTLE:DC

Sets the equalization CTLE Pole1 parameter.

CALCulate:TDR:EQUalization:CTLE:POLE1

Sets the equalization CTLE Pole2 parameter.

CALCulate:TDR:EQUalization:CTLE:POLE2

Sets the equalization CTLE zero parameter.

CALCulate:TDR:EQUalization:CTLE:ZERO1

Sets the filename of the equalization equation user file.

CALCulate:TDR:EQUalization:FILename

Turns the equalization function state ON or OFF.

CALCulate:TDR:EQUalization:STATe

Sets the equalization type.

CALCulate:TDR:EQUalization:TYPE

Executes the calculation for the simulated eye diagram for the active trace.

CALCulate:TDR:EYE:EXECute

Sets the bits' power of 2 for a PRBS pattern.

CALCulate:TDR:EYE:INPut:BPATtern:LENGth

Sets the bit pattern type for the simulated eye function.

CALCulate:TDR:EYE:INPut:BPATtern:TYPE

Sets the bit rate in bits/sec for the simulated eye function.

CALCulate:TDR:EYE:INPut:DRATe

Sets the display limit value.

CALCulate:TDR:EYE:INPut:JITTer:DLIMit

Sets the periodic jitter frequency.

CALCulate:TDR:EYE:INPut:JITTer:PERiodic:FREQuency

Sets the periodic jitter magnitude in rms.

CALCulate:TDR:EYE:INPut:JITTer:PERiodic:MAGNitude

Sets the random jitter magnitude in rms

CALCulate:TDR:EYE:INPut:JITTer:RANDom:MAGNitude

Turns the jitter function state with simulated eye ON or OFF.

CALCulate:TDR:EYE:INPut:JITTer:STATe

Sets the jitter function type for the simulated eye function.

CALCulate:TDR:EYE:INPut:JITTer:TYPE

Sets the voltage level for bit "1" for the simulated eye function.

CALCulate:TDR:EYE:INPut:OLEVel

Sets the rise time value for the simulated eye function.

CALCulate:TDR:EYE:INPut:RTIMe:DATA

Sets the rise time threshold for the simulated eye.

CALCulate:TDR:EYE:INPut:RTIMe:THReshold

Sets the voltage level for bit "0" for the simulated eye function.

CALCulate:TDR:EYE:INPut:ZLEVel

Returns the mask test result.

CALCulate:TDR:EYE:MASK:FAIL?

Turns the mask test function state with simulated eye ON or OFF.

CALCulate:TDR:EYE:MASK:STATe

Returns the results of the eye measurement.

CALCulate:TDR:EYE:RESults:DATA?

Turns the overlay ON or OFF.

CALCulate:TDR:EYE:RESults:DISPlay:STATe

Sets the rise time threshold level for the results of eye measurement.

CALCulate:TDR:EYE:RESults:THReshold

Turns the Eye/Mask window ON or OFF.

CALCulate:TDR:EYE:STATe

Sets active marker number.

CALCulate:TDR:MEASure[1-16]:ACTive:MARKer

Returns the delta time result value.

CALCulate:TDR:MEASure[1-16]:DTIMe:DATA?

Sets delta time reference position.

CALCulate:TDR:MEASure[1-16]:DTIMe:POSition

Turns the delta time marker in the marker search ON or OFF.

CALCulate:TDR:MEASure[1-16]:DTIMe:STATe

Sets the target trace number for the delta time function.

CALCulate:TDR:MEASure[1-16]:DTIMe:TARGet

Sets the trace format.

CALCulate:TDR:MEASure[1-16]:FORMat

Sets the measurement parameter.

CALCulate:TDR:MEASure[1-16]:PARameter

Sets state for the peeling function.

CALCulate:TDR:MEASure[1-16]:PEELing:STATe

Sets state for the smoothing function.

CALCulate:TDR:MEASure[1-16]:SMOothing:STATe

Sets the impulse width value for the transform function.

CALCulate:TDR:MEASure[1-16]:TIME:IMPulse:WIDTh

Sets rise time value for the transform function.

CALCulate:TDR:MEASure[1-16]:TIME:STEP:RTIMe

Sets the rise time threshold level for the results of eye measurement.

CALCulate:TDR:MEASure[1-16]:TIME:STEP:RTIMe:THReshold

Sets the stimulus type for the transform function.

CALCulate:TDR:MEASure[1-16]:TIME:TYPE

Returns the rise time result value for marker search.

CALCulate:TDR:MEASure[1-16]:TTIMe:DATA?

Displays the rise time marker.

CALCulate:TDR:MEASure[1-16]:TTIMe:STATe

Sets the rise time threshold for the rise time in the marker search function.

CALCulate:TDR:MEASure[1-16]:TTIMe:THReshold

Display TDR Commands

Turns the continuous auto-scale mode for the eye y-axis ON or OFF.

DISPlay:TDR:EYE:Y:SCALe:AUTO:STATe

Sets the value of the y-axis scale per division for eye diagram.

DISPlay:TDR:EYE:Y:SCALe:PDIVision

Sets the value of the eye diagram y-axis reference line.

DISPlay:TDR:EYE:Y:SCALe:RLEVel

Sets the value of the eye diagram y-axis reference position.

DISPlay:TDR:EYE:Y:SCALe:RPOSition

Changes the background color of the screen.

DISPlay:TDR:IMAGe

Sets the display to off, data type, memory type, or data and memory type.

DISPlay:TDR:MEASure[1-16]:DMEMory:TYPE

Executes x-axis auto scaling.

DISPlay:TDR:MEASure[1-16]:X:SCALe:AUTO

Sets the value of the x-axis scale per division.

DISPlay:TDR:MEASure[1-16]:X:SCALe:PDIVision

Sets the value of the x-axis reference line.

DISPlay:TDR:MEASure[1-16]:X:SCALe:RLEVel

Executes y-axis auto scaling.

DISPlay:TDR:SCALe:AUTO

Sets the x-axis reference position for the time domain measurement.

DISPlay:TDR:SCALe:RPOSition

Selects the view point for waveform analysis either before or after the DUT.

DISPlay:TDR:VIEW

Sets or gets the minimize state.

DISPlay:TDR:MINimize:STATe

Memory TDR Commands

Loads the specified user bit pattern file.

MMEMory:TDR:LOAD[:EYE]:BPATtern

Loads eye-mask file.

MMEMory:TDR:LOAD[:EYE][:MASK]

Stores the user bit pattern file.

MMEMory:TDR:STORe[:EYE]:BPATtern

Stores the eye-mask file.

MMEMory:TDR:STORe[:EYE][:MASK]

Correction TDR Commands

Executes load measurement.

SENSe:CORRection:TDR:COLLection:DLComp:LOAD

Executes open measurement.

SENSe:CORRection:TDR:COLLection:DLComp:OPEN

Saves the result of the Loss Compensation sequence.

SENSe:CORRection:TDR:COLLection:DLComp:SAVE

Executes a thru measurement.

SENSe:CORRection:TDR:COLLection:DLComp:THRU

Executes fixture compensation after ECAL.

SENSe:CORRection:TDR:COLLection:ECAL:FCOMp:IMMediate

Executes full calibration using the ECal module.

SENSe:CORRection:TDR:COLLection:ECAL:IMMediate

Sets the dielectric constant value.

SENSe:CORRection:TDR:DCONstant

Executes deskew (auto port extension).

SENSe:CORRection:TDR:EXTension:AUTO:IMMediate

Sets the standard for auto port extension.

SENSe:CORRection:TDR:EXTension:AUTO:STANdard

Sets the reference impedance value.

SENSe:CORRection:TDR:RIMPedance

Bandwidth, DUT information, avoid spurious function, and sweep TDR Commands

Sets the IF bandwidth value.

SENSe:TDR:BWIDth[:RESolution]

Executes auto DUT length setting.

SENSe:TDR:DLENgth:AUTO:IMMediate

Sets the DUT length value.

SENSe:TDR:DLENgth:DATA

Executes avoid spurious.

SENSe:TDR:SPURious:AVOid:IMMediate

Queries the avoid spurious state.

SENSe:TDR:SPURious:AVOid:STATe?

Sets the value of input bit rate for avoid spurious.

SENSe:TDR:SPURious:INPut:DRATe

Queries the Hot TDR mode status.

SENSe:TDR:SPURious:STATe?

Sets the TDR averaging trigger state on/off.

SENSe:TDR:SWEep:AVERage

Sets trigger mode.

SENSe:TDR:SWEep:MODE

Executes single trigger.

SENSe:TDR:SWEep:SINGle

Enables/disables the Reduce IF BW at Low Frequencies feature in segments with IFBW arbitrary.

SENSe:TDR:BWIDth:TRACk:FORCe

Source Power Level TDR Command

Sets the source power level.

SOURce:TDR:POWer[:LEVel][:IMMediate][:AMPLitude]

Preset TDR Command

Executes a TDR preset.

SYSTem:TDR:PRESet

Modulation Distortion Commands

Sets and returns the noise bandwidth.

SENSe:SA:BANDwidth:NOISe

Enable or disable setting the noise bandwidth to its maximum possible value.

SENSe:SA:BANDwidth:NOISe:AUTO

Selects between a narrow and wide IF filter anti-aliasing path.

SENSe:DISTortion:ADC:FILTer:TYPE

This command launches the Receiver IF Cal.

SENSe<cnum>:DISTortion:CORRection:COLLect:IF:ACQuire [SYNChronous | ASYNchronous]

Identifies the normalization used for the EVM measurements.

SENSe:DISTortion:EVM:NORMalize

Sets and returns the frequency span window used for modeling the DUT's gain and distortion.

SENSe:DISTortion:MEASure:CORRelation:APERture

Enable or disable automatic calculation of the frequency span window used for modeling the DUT's gain and distortion.

SENSe:DISTortion:MEASure:CORRelation:APERture:AUTO[:STATe]

Sets and returns the integration bandwidth (IBW) of the lower ACP measurement.

SENSe:DISTortion:MEASure:BAND:ACP:LOWer:IBW

Sets and returns the lower ACP measurement offset.

SENSe:DISTortion:MEASure:BAND:ACP:LOWer:OFFSet

Sets and returns the integration bandwidth (IBW) of the upper ACP measurement.

SENSe:DISTortion:MEASure:BAND:ACP:UPPer:IBW

Sets and returns the upper ACP measurement offset.

SENSe:DISTortion:MEASure:BAND:ACP:UPPer:OFFSet

Adds a new distortion measurement band.

SENSe:DISTortion:MEASure:BAND:ADD

Automatically fills in the measurement settings for all bands from the currently active modulation file loaded in the source.

SENSe:DISTortion:MEASure:BAND:AUTofill

Sets and returns the carrier (Signal) integration bandwidth (IBW) for the distortion measurement.

SENSe:DISTortion:MEASure:BAND:CARRier:IBW

Sets and returns the carrier offset (Signal).

SENSe:DISTortion:MEASure:BAND:CARRier:OFFSet

Queries the total number of distortion measurement bands.

SENSe:DISTortion:MEASure:BAND:COUNt?

Deletes the specified distortion measurement band.

SENSe:DISTortion:MEASure:BAND:DELete

Deletes all existing bands and adds a single default band back into the Measurement Band Table.

SENSe:DISTortion:MEASure:BAND:INITialize

Assigns a name to the specified distortion measurement band.

SENSe:DISTortion:MEASure:BAND:NAME

Sets and returns the notch integration bandwidth (IBW) for an NPR Notch modulation measurement.

SENSe:DISTortion:MEASure:BAND:NOTCh:IBW

Sets and returns the notch offset for an NPR Notch modulation measurement.

SENSe:DISTortion:MEASure:BAND:NOTCh:OFFSet

Set and read the modulation distortion type.

SENSe:DISTortion:MEASure:BAND:TYPE

Sets the measurement filter to either None (default) or RRC (root-raised-cosine filter)

SENSe:DISTortion:MEASure:FILTer

Sets and returns the Alpha factor of the measurement filter.

SENSe:DISTortion:MEASure:FILTer:ALPHa

Sets and returns the Symbol Rate of the filter.

SENSe:DISTortion:MEASure:FILTer:SRATe

Enables or disables using the symbol rate from the file.

SENSe:DISTortion:MEASure:FILTer:SRATe:AUTO[:STATe]

Sets and returns the distortion modulation source name.

SENSe:DISTortion:MODulate:SOURce

Sets and returns the VNA port number connected to the DUT input.

SENSe:DISTortion:PATH:DUT:INPut

Sets and returns the nominal DUT gain.

SENSe:DISTortion:PATH:DUT:NOMinal:GAIN

Sets and returns the nominal DUT noise figure.

SENSe:DISTortion:PATH:DUT:NOMinal:NF

Include or exclude the NF nominal value.

SENSe:DISTortion:PATH:DUT:NOMinal:NF:INCLude

None

Sets and returns the VNA port number connected to the DUT output.

SENSe:DISTortion:PATH:DUT:OUTPut

Enables or disables the external modulated source to pass through the attenuator of the specified PNA source

SENSe:DISTortion:PATH:SOURce:ATTenuation:INCLude

Sets and returns the nominal gain of an external source amplifier.

SENSe:DISTortion:PATH:SOURce:NOMinal:AMPLifier

Enables or disables receiver timing auto generation from the source pulse timing.

SENSe:DISTortion:PULSe:RECeiver:AUTO

Sets and returns the carrier center frequency.

SENSe:DISTortion:SWEep:CARRier:FREQuency

Selects between a ramp type power sweep or a list of power values to define a power sweep.

SENSe:DISTortion:SWEep:POWer:CARRier:LEVel:TYPE

Adds a new row to the power sweep list table.

SENSe:DISTortion:SWEep:POWer:CARRier:LIST:ADD

Deletes the specified row from the power sweep list table.

SENSe:DISTortion:SWEep:POWer:CARRier:LIST:DELete

Sets and returns the power level used for the specified row in the power sweep list table.

SENSe:DISTortion:SWEep:POWer:CARRier:LIST:LEVel

Specifies the file path to recall a previous power sweep list file.

SENSe:DISTortion:SWEep:POWer:CARRier:LIST:LOAD

Sets and returns the noise bandwidth setting used for the specified row in the power sweep list table.

SENSe:DISTortion:SWEep:POWer:CARRier:LIST:NBW

Selects the noise bandwidth mode in the power sweep list table.

SENSe:DISTortion:SWEep:POWer:CARRier:LIST:NBW:MODE

Sets and returns the number of power points to measure for the power sweep list measurement.

SENSe:DISTortion:SWEep:POWer:CARRier:LIST:POINts

Sets and returns the receiver attenuation for the specified row in the power sweep list table.

SENSe:DISTortion:SWEep:POWer:CARRier:LIST:RECeiver:ATTenuation

Selects the receiver attenuation mode in the power sweep list table.

SENSe:DISTortion:SWEep:POWer:CARRier:LIST:RECeiver:ATTenuation:MODE

Specifies the file path to save a power sweep list file.

SENSe:DISTortion:SWEep:POWer:CARRier:LIST:SAVE

Sets and returns the source attenuation for the specified row in the power sweep list table.

SENSe:DISTortion:SWEep:POWer:CARRier:LIST:SOURce:ATTenuation

Selects the source attenuation mode in the power sweep list table.

SENSe:DISTortion:SWEep:POWer:CARRier:LIST:SOURce:ATTenuation:MODE

Sets and returns the starting power level for the power sweep ramp measurement.

SENSe:DISTortion:SWEep:POWer:CARRier:RAMP:LEVel:STARt

Sets and returns the stop power level for the power sweep ramp measurement.

SENSe:DISTortion:SWEep:POWer:CARRier:RAMP:LEVel:STOP

Enable or disable increasing noise bandwidth at high powers automatically for faster measurements.

SENSe:DISTortion:SWEep:POWer:CARRier:RAMP:NBW:AUTO

Sets and returns the number of power points to measure for the power sweep ramp measurement.

SENSe:DISTortion:SWEep:POWer:CARRier:RAMP:POINts

Enable or disable the re-use of the previous linear S-parameter measurements if available and skip sweep.

SENSe:DISTortion:SWEep:SPARam:REUSe

Enable or disable noise sweep used for the distortion test.

SENSe:DISTortion:SWEep:NOISe

Enables or disables S-parameter sweep.

SENSe:DISTortion:SWEep:SPARam[:STATe]

Sets and returns the power level used to measure the DUT gain when operating in its linear region.

SENSe:DISTortion:SWEep:POWer:SPARam:LEVel

Sets and returns the IF bandwidth for the linear S21 sweep.

SENSe:DISTortion:SWEep:SPARam:BWIDth

Sets and returns the step size for the linear S21 sweep.

SENSe:DISTortion:SWEep:SPARam:STEP

 Selects between a chirp signal from the external signal generator or an internal CW signal in the VNA for measuring S-parameters.

SENSe:DISTortion:SWEep:SPARam:TYPE

Sets and returns the power level used for the distortion test at either the input or output of the DUT.

SENSe:DISTortion:SWEep:POWer:CARRier:LEVel

Set and read where to apply power to the DUT (input or output).

SENSe:DISTortion:SWEep:POWer:CARRier:LEVel:PORT

Keeps RF power ON at the End of Sweep.

SENSe:DISTortion:SWEep:RETRace:POWer

Sets and returns the delay in seconds before the test signal to allow the RF source to settle.

SENSe:DISTortion:SWEep:DWELl

Selects between a fixed or power sweep type of sweep.

SENSe:DISTortion:SWEep:TYPE

Specifies the file path to save a modulation distortion table file.

SENSe:DISTortion:TABLe:DISPlay:SAVE

Sort distortion table by band or power.

SENSe:DISTortion:TABLe:DISPlay:SORT

LO Feedthru Monitor Commands

Return the last monitor result of LO feedthru monitor.

SENSe:SA:COHerance:LO:FTHRu:MONitor:LAST:FAILed

Return the last monitor value of LO feedthru monitor.

SENSe:SA:COHerance:LO:FTHRu:MONitor:LAST:VALue

Set and read the target receiver for LO Feedthru monitor.

SENSe:SA:COHerance:LO:FTHRu:MONitor:RECeiver

Set and read the LO feedthru monitoring state.

SENSe:SA:COHerence:LO:FTHRu:MONitor[:STATe]

Set and read the threshold level for warning.

SENSe:SA:COHerence:LO:FTHRu:MONitor:TOLerance

Set and read the monitoring method for LO feedthru monitor.

SENSe:SA:COHerence:LO:FTHRu:MONitor:TYPE

Calibrate Source Modulation Commands

Set and read the ACP modulation calibration state.

SOURce:MODulation:CORRection:COLLection:ACP:ENABle

Sets and reads the maximum number of iterations for the lower ACP modulation calibration.

SOURce:MODulation:CORRection:COLLection:ACP:LOWer:ITERations

Sets and reads the receiver for the lower ACP modulation calibration.

SOURce:MODulation:CORRection:COLLection:ACP:LOWer:RECeiver

Sets and reads the calibration span for a lower ACP modulation calibration.

SOURce:MODulation:CORRection:COLLection:ACP:LOWer:SPAN

Sets and reads the desired ACP calibration tolerance for the lower ACP modulation calibration.

SOURce:MODulation:CORRection:COLLection:ACP:LOWer:TOLerance

Enables or disables the upper ACP (ACPUp) modulation calibration.

SOURce:MODulation:CORRection:COLLection:ACP:UPPer:ENABle

Sets and reads the maximum number of iterations for the upper ACP modulation calibration.

SOURce:MODulation:CORRection:COLLection:ACP:UPPer:ITERations

Sets and reads the receiver for the upper ACP modulation calibration.

SOURce:MODulation:CORRection:COLLection:ACP:UPPer:RECeiver

Sets and reads the calibration span for an upper ACP modulation calibration.

SOURce:MODulation:CORRection:COLLection:ACP:UPPer:SPAN

Sets and reads the desired ACP calibration tolerance for the upper ACP modulation calibration.

SOURce:MODulation:CORRection:COLLection:ACP:UPPer:TOLerance

Setsand reads  the ACP lower  frequency delta from the edge of the carrier to the beginning of the Cal Span.

Sets and reads the ACP upper frequency delta from the edge of the carrier to the beginning of the calibration span.

Enable or disable the distortion calibration state.

SOURce:MODulation:CORRection:COLLection:DISTortion:ENABle

Sets and reads the maximum number of iterations used by the calibration routine.

SOURce:MODulation:CORRection:COLLection:DISTortion:ITERations

Sets and reads the receiver for distortion calibration.

SOURce:MODulation:CORRection:COLLection:DISTortion:RECeiver

Sets and reads the calibration span for a distortion calibration.

SOURce:MODulation:CORRection:COLLection:DISTortion:SPAN

Sets and reads the desired distortion calibration tolerance.

SOURce:MODulation:CORRection:COLLection:DISTortion:TOLerance

Enable or disable the equalization calibration state.

SOURce:MODulation:CORRection:COLLection:EQUalization:ENABle

Sets and reads the maximum number of iterations used by the calibration routine.

SOURce:MODulation:CORRection:COLLection:EQUalization:ITERations

Sets and reads the receiver for equalization calibration.

SOURce:MODulation:CORRection:COLLection:EQUalization:RECeiver

Sets and reads the calibration span for a equalization calibration.

SOURce:MODulation:CORRection:COLLection:EQUalization:SPAN

Sets and reads the desired equalization calibration tolerance.

SOURce:MODulation:CORRection:COLLection:EQUalization:TOLerance

Returns a list of  the calibrations stored in the .mdx file.

SOURce:MODulation:FILE:CORRection:CATalog?

Deletes any of the calibration files stored in the .mdx file.

SOURce:MODulation:FILE:CORRection:DELete?

Returns the frequency of the specified source modulation calibration file.

SOURce:MODulation:FILE:CORRection:FREQuency?

Returns the power level of the specified source modulation calibration file.

SOURce:MODulation:FILE:CORRection:POWer?

Append source modulation calibration files stored in the .mdx file.

SOURce:MODulation:CORRection:COLLection:APPend

Sets and reads a fixed frequency.

SOURce:MODulation:CORRection:COLLection:FREQuency[:FIXed]

Sets and reads the number of frequency measurement points.

SOURce:MODulation:CORRection:COLLection:FREQuency:POINts

Sets and reads the start frequency to use for a swept frequency source modulation calibration.

SOURce:MODulation:CORRection:COLLection:FREQuency:STARt

Sets and reads the stop frequency to use for a swept frequency calibration.

SOURce:MODulation:CORRection:COLLection:FREQuency:STOP

Sets and reads the calibration frequency type to fixed or swept.

SOURce:MODulation:CORRection:COLLection:FREQuency:TYPE

Enable or disable the LO feedthru calibration state.

SOURce:MODulation:CORRection:COLLection:LO:FTHRu:ENABle

Sets and reads the maximum number of iterations used by the calibration routine.

SOURce:MODulation:CORRection:COLLection:LO:FTHRu:ITERations

Sets and reads the receiver for LO feedthru modulation calibration.

SOURce:MODulation:CORRection:COLLection:LO:FTHRu:RECeiver

Sets and reads the calibration span for a LO feedthru modulation calibration.

SOURce:MODulation:CORRection:COLLection:LO:FTHRu:SPAN

Sets and reads the desired LO feedthru modulation calibration tolerance.

SOURce:MODulation:CORRection:COLLection:LO:FTHRu:TOLerance

Sets and reads a fixed power level.

SOURce:MODulation:CORRection:COLLection:POWer[:FIXed]

Sets and reads the number of power measurement points.

SOURce:MODulation:CORRection:COLLection:POWer:POINts

Sets and reads the start power level to use for a swept calibration.

SOURce:MODulation:CORRection:COLLection:POWer:STARt

Sets and reads the stop power level to use for a swept calibration.

SOURce:MODulation:CORRection:COLLection:POWer:STOP

Sets and reads the calibration power type to fixed or swept.

SOURce:MODulation:CORRection:COLLection:POWer:TYPE

Create/Edit Modulation File

Sets and reads the source sample rate.

SOURce:MODulation:FILE:INITialize

Specifies the file path to recall a previous modulation file.

SOURce:MODulation:FILE:LOAD

Sets and reads the source sample rate.

SOURce:MODulation:FILE:SAVE

Sets and reads the Carrier offset value.

SOURce:MODulation:FILE:SIGNal:CARRier:OFFSet

Sets and reads the number of compact modulation files to create.

SOURce:MODulation:FILE:SIGNal:COMPact:FILE:NUMBer

Sets and reads the compact modulation file selection.

SOURce:MODulation:FILE:SIGNal:COMPact:FILE:NUMBer:SELect

Specifies the file path to recall a previous modulation file from which to create a compact signal.

SOURce:MODulation:FILE:SIGNal:COMPact:OFILe

Returns the peak-to-average value of the original signal.

SOURce:MODulation:FILE:SIGNal:COMPact:PAVG?

Returns the peak-to-average value of the signal created from the original signal.

SOURce:MODulation:FILE:SIGNal:COMPact:PAVG:CALCulated?

Sets and reads the Peak-to-Avg priority for Compact signals.

SOURce:MODulation:FILE:SIGNal:COMPact:PAVG:PRIority

Allows setup of multiple carriers when defining a multicarrier signal.

SOURce:MODulation:FILE:SIGNal:COMPact:SUBCarrier:NUMBer

Sets and reads the offset of the selected subcarrier.

SOURce:MODulation:FILE:SIGNal:COMPact:SUBCarrier:OFFSet

Sets and reads the span of the selected subcarrier.

SOURce:MODulation:FILE:SIGNal:COMPact:SUBCarrier:SPAN

Sets and reads where to start the compact signal within the original signal.

SOURce:MODulation:FILE:SIGNal:COMPact:TIME:STARt

Returns the calculated start time of the signal created from the original signal.

SOURce:MODulation:FILE:SIGNal:COMPact:TIME:STARt:CALCulated?

Sets and reads the start time priority for Compact signals.

SOURce:MODulation:FILE:SIGNal:COMPact:TIME:STARt:PRIority

Sets and reads the DAC scale as a percentage of full scale.

SOURce:MODulation:FILE:SIGNal:DAC:SCALing

Sets the NPR notch location type for the selected NPR Notch modulation type.

SOURce:MODulation:FILE:SIGNal:NPR:NOTCh:LOCation

Sets and reads the number of NPR notches for NPR Notch modulation type.

SOURce:MODulation:FILE:SIGNal:NPR:NOTCh:NUMBer

Sets and reads the NPR notch offset frequency of the selected notch.

SOURce:MODulation:FILE:SIGNal:NPR:NOTCh:OFFSet

Sets and reads the span of the selected notch.

SOURce:MODulation:FILE:SIGNal:NPR:NOTCh:SPAN

Enables or disables signal optimization settings.

SOURce:MODulation:FILE:SIGNal:OPTimize:ENABle

Sets and reads the number of decimal digits limit for calculated frequencies.

SOURce:MODulation:FILE:SIGNal:OPTimize:FREQuency:LIMit:DDIGits

Enables or disables the number of decimal digits limit for calculated frequencies.

SOURce:MODulation:FILE:SIGNal:OPTimize:FREQuency:LIMit:ENABle

Sets and reads the frequency tolerance value (in percent).

SOURce:MODulation:FILE:SIGNal:OPTimize:FREQuency:TOLerance

Sets and reads the number of test signal harmonics you want to be protected against.

SOURce:MODulation:FILE:SIGNal:OPTimize:HREJect

Sets and reads the maximum distance between each tone.

SOURce:MODulation:FILE:SIGNal:OPTimize:MAX:TONE:SPacing

Sets and reads the minimum number of tones.

SOURce:MODulation:FILE:SIGNal:OPTimize:MIN:TONE:NUMBer

Sets and reads theminimum waveform period.

SOURce:MODulation:FILE:SIGNal:OPTimize:MIN:WAVeform:PERiod

Enables or disables the rejection of Nyquist frequencies.

SOURce:MODulation:FILE:SIGNal:OPTimize:NYQReject:ENABle

Sets the optimize signal type.

SOURce:MODulation:FILE:SIGNal:OPTimize:TYPE

Returns the calculated peak-to-average value.

SOURce:MODulation:FILE:SIGNal:PAVG:CALCulated?

Sets and reads the phase when Fixed phase is the Phase Type.

SOURce:MODulation:FILE:SIGNal:PHASe:FIXed

Sets and reads the phase seed when Random phase is the Phase Type.

SOURce:MODulation:FILE:SIGNal:PHASe:RANDom:SEED

Sets the phase type.

SOURce:MODulation:FILE:SIGNal:PHASe:TYPE

Sets and reads the signal span.

SOURce:MODulation:FILE:SIGNal:SPAN

Returns the calculated signal span.

SOURce:MODulation:FILE:SIGNal:SPAN:CALCulated?

Sets and reads the signal span priority.

SOURce:MODulation:FILE:SIGNal:SPAN:PRIority

Sets and reads the source sample rate.

SOURce:MODulation:FILE:SIGNal:SRATe

Returns the calculated sampling rate of the signal created from the original signal.

SOURce:MODulation:FILE:SIGNal:SRATe:CALCulated?

Set and read the auto sample rate.

SOURce:MODulation:FILE:SIGNal:SRATe:AUTO

Sets and reads the number of tones.

SOURce:MODulation:FILE:SIGNal:TONE:NUMBer

Returns the calculated number of tones.

SOURce:MODulation:FILE:SIGNal:TONE:NUMBer:CALCulated?

Sets and reads the tone number priority.

SOURce:MODulation:FILE:SIGNal:TONE:NUMBer:PRIority

Sets and reads the tone spacing.

SOURce:MODulation:FILE:SIGNal:TONE:SPACing

Returns the calculated spacing between the tones.

SOURce:MODulation:FILE:SIGNal:TONE:SPACing:CALCulated?

Sets and reads the tone spacing priority.

SOURce:MODulation:FILE:SIGNal:TONE:SPACing:PRIority

Returns the number of tones.

SOURce:MODulation:FILE:TONE:NUMBer?

Returns the tone frequency in Hz relative to the carrier.

SOURce:MODulation:FILE:TONE:FREQuency?

Sets and reads the power in dBm of the specified tone number.

SOURce:MODulation:FILE:TONE:POWer

Sets and reads the phase in degrees of the specified tone number.

SOURce:MODulation:FILE:TONE:PHASe

Set specified tone state to on or off.

SOURce:MODulation:FILE:TONE[:STATe]

Set all tone states to on or off.

SOURce:MODulation:FILE:TONE:ALL[:STATe]

Saves the specified multitone file.

SOURce:MODulation:FILE:TONE:SAVE

Loads the specified multitone file.

SOURce:MODulation:FILE:TONE:LOAD

Sets the modulation type.

SOURce:MODulation:FILE:TYPE

Distortion Table Commands

Returns the currently displayed Distortion Table parameters.

SENSe:DISTortion:TABLe:DISPlay:CATalog?

Deletes the specified parameter from the Distortion Table.

SENSe:DISTortion:TABLe:DISPlay:DELete

Adds the specified parameter to the Distortion Table.

SENSe:DISTortion:TABLe:DISPlay:FEED

Returns a list of existing band names from the Measurement Band Table.

SENSe:DISTortion:TABLe:CATalog?

Returns a list of data parameter names corresponding to the currently specified Measurement Type.

SENSe:DISTortion:TABLe:DATA:CATalog?

Returns a list of data values from the Distortion Table for the specified band and parameter name.

SENSe:DISTortion:TABLe:DATA:VALue?

Modulation Distortion Marker Commands

Set and read the SA marker function type.

CALCulate:MEASure:SA:MARKer:BAND:FUNCtion

Sets and reads the integration bandwidth marker.

CALCulate:MEASure:SA:MARKer:BAND:IBW

Sets and reads the ACPR density marker.

CALCulate:MEASure:SA:MARKer:BDENsity:ACPR[:STATe]

CALCulate:SA:MARKer:BDENsity:ACPR[:STATe]

Sets and reads the NPR density marker.

CALCulate:MEASure:SA:MARKer:BDENsity:NPR[:STATe]

CALCulate:SA:MARKer:BDENsity:NPR[:STATe]

Executes the search ACPR density marker.

CALCulate:MEASure:SA:MARKer:SEARch:ACPR

Executes the search NPR density marker.

CALCulate:MEASure:SA:MARKer:SEARch:NPR

Measurement Data

Retrieves trace data (Y data) from the modulation distortion measurement.

CALCulate:MEASure:DATA:BUFFer:Y?

Retrieves frequency tone data from the modulation distortion measurement.

CALCulate:MEASure:DATA:BUFFer:X?