Setup Commands - Noise Figure Converters Measurement Class

Only the Main and Layout Setup commands corresponding to the Noise Figure Converters measurement class are documented here. All other commands are identical to the Setup commands for the Standard measurement class and can be accessed by clicking here or by clicking on the softtabs on the graphic below.

Click here to view links to Setup commands for all Measurement Classes.

Main

Layout

System
Setup

Internal
Hardware

External
Hardware

Main Tab Commands
Softkey	Sub-item	SCPI	COM
NFX Setup...	Frequency
	Sweep Type
	Linear Sweep	SENSe:SWEep:TYPE	SweepType
	CW Frequency	SENSe:SWEep:TYPE	SweepType
	X-Axis Display
	Annotation	CALCulate:MEASure:MIXer:XAXis	ActiveXAxisRange
	Sweep Settings
	Number of Points	SENSe:SWEep:POINts	NumberOfPoints
	IF Bandwidth	SENSe:BWIDth[:RESolution]	IFBandwidth
	Start	SENSe:FREQuency:STARt	StartFrequency
	Stop	SENSe:FREQuency:STOP	StopFrequency
	Center	SENSe:FREQuency:CENTer	CenterFrequency
	Span	SENSe:FREQuency:SPAN	FrequencySpan
	Power
	Power On (All Channels)	OUTPut[:STATe]	SourcePowerState
	Port Powers Coupled	SOURce:POWer:COUPle	CouplePorts
	DUT Input Port
	Input Port	SENSe:NOISe:PMAP	SetPortMap
	Power Level	SOURce:POWer[:LEVel][:IMMediate][:AMPLitude]	InputLinearPowerLevel
	Source Leveling Mode	SOURce:POWer:ALC[:MODE]	ALCLevelingMode
	DUT Output Port
	Output Port	SENSe:NOISe:PMAP	SetPortMap
	Power Level	SOURce:POWer[:LEVel][:IMMediate][:AMPLitude]	InputLinearPowerLevel
	Source Leveling Mode	SOURce:POWer:ALC[:MODE]	ALCLevelingMode
	Path Configuration...	SENSe:PATH:CONFig:ELEMent[:STATe]	Element
	Noise Figure
	Bandwidth/Average
	Noise Bandwidth	SENSe:NOISe:BWIDth[:RESolution]	NoiseBandwidth
	Average Number	SENSe:NOISe:AVERage[:COUNt]	NoiseAverageFactor
	Average ON	SENSe:NOISe:AVERage:STATe	NoiseAverageState
	Use Narrowband Compensation	SENSe:NOISe:NARRowband[:STATe]	NarrowBand
	Noise Receiver
	NA Receiver (Port 2)	SENSe:NOISe:RECeiver	NoiseReceiver
	Noise Receiver	SENSe:NOISe:RECeiver	NoiseReceiver
	Receiver Gain	SENSe:NOISe:GAIN	NoiseGain
	Source Temperature	SENSe:NOISe:TEMPerature:SOURce SENSe:NOISe:TEMPerature:SOURce:AUTO	None None
	Ambient Temperature	SENSe:NOISe:TEMPerature:AMBient	AmbientTemperature
	Impedance States
	Max Acquired Impedance States	SENSe:NOISe:IMPedance:COUNt	ImpedanceStates
	Enable Source Pulling for SParameters	SENSe:NOISe:PULL[:STATe]	SourcePullForSParameters
	Mixer Frequency
	Input	SENSe:MIXer:CALCulate	Calculate
	LO1	SENSe:MIXer:LO:FREQuency:FIXed	LOFixedFrequency
	Input > LO	SENSe:MIXer:LO:FREQuency:ILTI	IsInputGreaterThanLO
	Output	SENSe:MIXer:CALCulate	Calculate
	Mixer Power
	Power On (All Channels)	OUTPut[:STATe]	SourcePowerState
	LO1 Power	SENSe:MIXer:LO:POWer	LOPower
	LO2 Power	SENSe:MIXer:LO:POWer	LOPower
	LO1 Swept Power
	Start	SENSe:MIXer:LO:FREQuency:STARt	LOStartFrequency
	Stop	SENSe:MIXer:LO:FREQuency:STOP	LOStopFrequency
	Step	None	None
	LO2 Swept Power
	Start	SENSe:MIXer:LO:FREQuency:STARt	LOStartFrequency
	Stop	SENSe:MIXer:LO:FREQuency:STOP	LOStopFrequency
	Step	None	None
	Path Configuration...	SENSe:PATH:CONFig:ELEMent[:STATe]	Element
	Mixer Setup
	Converter Stages	SENSe:MIXer:STAGe	LOStage
	Add Source...	SENSe:ROLE:DEVice	AssignSourceToRole
	Path Configuration...	SENSe:PATH:CONFig:ELEMent[:STATe]	Element
	Save...	SENSe:MIXer:SAVE	SaveFile
	Load...	SENSe:MIXer:LOAD	LoadFile
Meas Class...		CALCulate:MEASure:DEFine	CreateCustomMeasurementEx
Quick Start...	S-Param	CALCulate:MEASure:PARameter	CreateSParameterEx
	Balanced	CALCulate:MEASure:PARameter	BalSMeasurement BBalMeasurement SBalMeasurement SSBMeasurement
	Other	CALCulate:MEASure:PARameter	CreateSParameterEx
Layout Tab Commands
Softkey	Sub-item	SCPI	COM
New Trace		DISPlay:WINDow:TRACe[:STATe]	View
New Channel		None	chans.Add
New Window		DISPlay:WINDow[:STATe]	Add
New Sheet		DISPlay:SHEet:STATe	None
Delete	TrN	DISPlay:WINDow:TRACe:DELete	None
	ChN	SYSTem:CHANnels:DELete	RemoveChannelNumber
	WinN	DISPlay:WINDow[:STATe]	Add
Select	TrN	DISPlay:WINDow:TRACe:SELect	None
	ChN	None	None
	WinN	DISPlay:WINDow:TRACe:SELect	None
Measure...		CALCulate:MEASure:PARameter	CreateSParameterEx
Meas Class...		CALCulate:MEASure:DEFine	CreateCustomMeasurementEx