Main Tab Commands | |||
Softkey | Sub-item | SCPI |
COM |
Show Taskbar | None |
None |
|
Move App to Back | None |
None |
|
Minimize Application | None |
None |
|
Exit | None | ||
Security... | SYSTem:SECurity[:LEVel] | ||
Control Panel... | None |
None |
|
Manage Files... | List Files | MMEMory:CATalog |
None |
Copy Files | MMEMory:COPY |
None |
|
Move Files | MMEMory:MOVE |
None |
|
Delete Files | MMEMory:DELete |
None |
|
System Setup Tab Commands | |||
Softkey | Sub-item | SCPI |
COM |
Next/Prev Keys | Trace | None |
None |
Channel | None |
None |
|
Window | None |
None |
|
Sheet | None |
None |
|
Preferences... | Avg: On Preset set two-point Group Delay Aperture | SYSTem:PREFerences:ITEM:GDELay:TWOPoint | |
Avg: Calculate Group Delay using legacy PNA Math |
|||
Cal: Always merge when saving Cal in Cal Set | None |
None |
|
Cal: Always use Internal trigger during cal | None |
None |
|
Cal: ECal Extrapolation for IMD | None |
None |
|
Cal: For Frequency Offset, use Primary frequencies | SENSe:CORRection:PREFerences:CALibration[:FOM]:RANGe | ||
Cal: (SCPI only) Auto-generate a User Cal Set | SENSe:CORRection:CSET:CREate | ||
Cal: (SCPI only) Auto-save to current Cal Set | SENSe:CORRection:PREFerence:CSET:SAVE | ||
Cal: Turn off RF Power after calibration | SYSTem:PREFerence:ITEM:CALibration:SAFE[:STATe] | None | |
Cal: Use legacy behavior for Series-C & Shunt-L fixtures |
None |
||
Cal: Use Unknown thru math for SOLT methods | SYSTem:PREFerence:ITEM:USOLt |
None |
|
Display: Selected trace changes width briefly | None |
None |
|
Display: Selected trace is wider | None |
None |
|
Display: Touchscreen On | SYSTem:TOUChscreen[:STATe] | ||
Ext Device: De-activate on Preset and Recall | SYSTem:PREFerences:ITEM:EDEV:DPOLicy | ||
Ext Reference: Modify Settings on Preset and Recall | SYSTem:PREFerences:ITEM:ROSCillator:RECall |
None |
|
Limit: Draw failed trace segments in red | SYSTem:PREFerences:ITEM:RTOF | ||
Limit: Draw limit lines in red | SYSTem:PREFerences:ITEM:REDLimits | ||
Limit: Test the nearest measurement point | None |
None |
|
Marker: Coupling controls on/off state of markers | SYSTem:PREFerences:ITEM:MCControl | ||
Marker: On Preset, Coupled Markers is On | SYSTem:PREFerences:ITEM:MCPreset | ||
Marker: On Preset, Coupling Method is Channel | SYSTem:PREFerences:ITEM:MCMethod | ||
Marker: On Preset, set BW/Notch search reference to Peak | SYSTem:PREFerences:ITEM:MARKer:BANDwidth:SEARch | ||
Marker: Programming treats Mkr 10 as Reference | SYSTem:PREFerences:ITEM:REFMarker | ||
Marker: Use single marker for marker search | SYSTem:PREFerences:ITEM:MARKer:SINGle | ||
Meas: Mathematical offset for receiver attenuation | SYSTem:PREFerences:ITEM:OFFSet:RCV | ||
Meas: Mathematical offset for source attenuation | SYSTem:PREFerences:ITEM:OFFSet:SRC | ||
Memory: Data Math 8510 Mode | None |
None |
|
Memory: Interpolate ON is default condition | SYSTem:PREFerences:ITEM:MINTerpolate | ||
Power: On Preset turn power off | SYSTem:PREFerences:ITEM:PRESet:POWer | ||
Power: On Preset turn power on | SYSTem:PREFerences:ITEM:PRESet:POWer | ||
Power: Report source unleveled events as errors | SYSTem:ERRor:REPort:SUNLeveled | ||
Power: Report when receiver is overloaded | SYSTem:PREFerences:ITEM:RECeivers:CERRor | ||
Power: Force RF power Off at the end of sweep | SYSTem:PREFerences:ITEM:RETRace:POWer | ||
Power: Turn Source Power Off when receiver is overloaded | SYSTem:PREFerences:ITEM:RECeivers:OVERload:POWer | ||
Power: Use Start Power during Power Sweep retrace | SYSTem:PREFerences:ITEM:PSRTrace | ||
Preset: Confirm preset | SYSTem:PREFerences:ITEM:PRESet:CONFirm | ||
Preset: On Preset show Quick Start dialog | SYSTem:PREFerences:ITEM:QSTart | ||
Recall: Softkey order is most recently used | None |
None |
|
Scale: On Preset Couple Scale to Window | None |
None |
|
Sweep: On Preset set Sweep Mode to Stepped | None |
None |
|
Sweep: Use only ramp sweeps for Auto Sweep Mode | SYSTem:PREFerences:ITEM:ASMRamp |
None |
|
System: Enable sound | SYSTem:BEEP:STATe |
None |
|
System: On Power-on show dialog if detect mm testset | None |
None |
|
System: On Power-on show Keys toolbar | SYSTem:PREFerences:ITEM:Keys | ||
System: Use keyboard to navigate softkeys | SYSTem:PREFerences:ITEM:SOFTkeys:NAVigation |
None |
|
System: Use parallel processing |
None |
||
System: Set front panel remote state when a SCPI command is received | SYSTem:PREFerences:ITEM:REMote:AUTO[:STATe] |
None |
|
Trigger: External Trigger Out is Global | TRIGger:PREFerences:AIGLobal | ||
Data Saves... | MMEMory:STORe:DATA | ||
Power Limit... | SYSTem:POWer:LIMit | ||
Transparency... | None |
None |
|
User Preset... | SYSTem:UPReset | ||
Page Setup... | Hardcopy |
None |
|
Disp Colors... | See Display | ||
Print Colors... | See Display | See Display | |
Power On (All Channels) |
None |
None |
|
Global Sources Ignore "Power ON" Setting |
None |
||
Global |
None |
||
State |
None |
||
Frequency |
None |
||
Power |
None |
||
Sound |
None |
||
Remote Interface... | GPIB Address | None | |
SICL Enabled | None | ||
SICL Address | None | ||
Automatically Enable on Startup | None |
None |
|
Sockets Enabled | None |
None |
|
Telnet Enabled | None |
None |
|
HiSLIP Enabled | None | ||
HiSLIP Address | None | ||
Enable Remote Drive Access | SYSTem:COMMunicate:DRIVe:ENABle? |
None |
|
Show SCPI Parser Console | None |
None |
|
Monitor GPIB Bus | None |
None |
|
None |
|||
Print Tab Commands | |||
Softkey | Sub-item | SCPI |
COM |
Print... | HCOPy:DPRinter | ||
Print to File... | HCOPy:FILE | ||
Page Setup... | Hardcopy |
None |
|
Print Colors... | Pen | ||
Background | DISPlay:COLor:BACKground | ||
Active Background | DISPlay:COLor:ABACkground | ||
Grid | DISPlay:COLor:GRAT2 | ||
Active Labels, Grid frame | DISPlay:COLor:GRAT1 | ||
Inactive Window Labels | DISPlay:COLor:ILABel | ||
Failed Trace | DISPlay:COLor:LIM1 | ||
N Trace: Data and Limits | DISPlay:COLor:TRACe:DATA | ||
N Trace: Memory | DISPlay:COLor:TRACe:MEMory | ||
N Trace: Markers | DISPlay:COLor:TRACe:MARKer | ||
N Trace: Memory Markers | DISPlay:COLor:TRACe:MMARker | ||
Change Color... | None |
None |
|
Reset Color | DISPlay:COLor:RESet |
None |
|
Color Theme | |||
Save Theme... | DISPlay:COLor:STORe | ||
Recall Theme... | DISPlay:COLor:LOAD | ||
Reset Theme | DISPlay:COLor:RESet | ||
Help Tab Commands | |||
Softkey | Sub-item | SCPI |
COM |
NA Help... | None |
None |
|
On The Web... | None |
None |
|
Error Display... | Enable Messages | DISPlay:ANNotation:MESSage:STATe |
None |
Status bar Display | DISPlay:ANNotation[:STATus] | ||
Confirmation Dialog boxes | None |
None |
|
View Error Log... | None |
None |
|
Tech Support | PathWave Calibration Advisor Commands |
SYSTem:CAPability:LICenses:FEATure:CATalog? SYSTem:CAPability:LICenses:FEATure:ENABle? SYSTem:SERVice:MANagement:CALibration:INFormation? SYSTem:SERVice:MANagement:CALibration:INTerval:DEFault SYSTem:SERVice:MANagement:CALibration:INTerval:TYPE? SYSTem:SERVice:MANagement:CALibration:INTerval[:VALue] SYSTem:SERVice:MANagement:CALibration:NOTification:ENABle SYSTem:SERVice:MANagement:CALibration:PASScode:CHANge SYSTem:SERVice:MANagement:CALibration:PASScode[:VALue] |
None None None NoneNone None None None None None None |
About NA... | None |
None |
|
Service Tab Commands | |||
Softkey | Sub-item | SCPI |
COM |
Update Firmware |
None |
None |
|
Verification |
None |
None |
|
Adjustment Routines... | None |
None |
|
Diagnostics |
None |
None |
|
Option Enable |
None |
None |