In this topic:
- Commands that are Common to All Modes
|
Description |
Command |
|
Set/query the data format for data transfer |
|
|
Set/query the data format that data is read (binary or ASCii) |
|
Description |
Command |
|
Sets the antenna orientation |
SYSTem:ANTenna:USB:AXIS (SUPERSEDED) is not recommended and has a new recommended behavior: |
|
Import antenna correction factors from USB antenna. |
SYSTem:ANTenna:USB:IMPort (SUPERSEDED) is not recommended and has a new recommended behavior: |
|
Import antenna correction factors CSV file for EMF antenna type FSH3D |
|
| Sets antenna type |
SYSTem:ANTenna:USB:TYPe (SUPERSEDED) is not recommended and has a new recommended behavior: |
|
Description |
Command |
|
Enables Instalign, before the next sweep |
|
|
Align all state (coupled to all individual alignments) |
|
|
Align now (coupled to all individual alignments) |
|
|
InstAlign state |
|
Description |
Command |
|
Query a file catalog |
|
|
Enables front panel key press control |
|
|
Disables front panel key press control (Lockout) |
|
|
Sets the remote lockout message |
|
|
Sets the current mode |
|
Description |
Command |
|
Set/query frequency mode |
|
|
Set/query CW frequency |
|
Description |
Command |
|
Number of averages |
|
|
Set/query the averaging state |
|
Description |
Command |
|
Set/query display brightness |
|
|
Set/query system date format |
|
|
Enables/disables the FieldFox display |
|
|
Set/query keywords for creating filenames |
|
|
Reset filename keywords to their default values |
|
|
Set/query display mode |
|
|
Set/query the formatting of the system time |
|
|
Set/query the FieldFox display data title |
|
|
Set/query the display title state |
|
Description |
Command |
|
Clear the calibration |
|
|
Initiate and save the calibration |
|
|
Cancel calibration |
|
|
Load calibration file |
|
|
Query calibration status |
|
|
Enable calibration status |
|
|
Query Questionable Calibration Event register |
|
|
Questionable Calibration Event Register when the bit has a negative transition |
|
|
Questionable Calibration Event Register when the bit has a positive transition |
|
Description |
Command |
|
Set/query AM depth |
|
|
Set/query AM rate |
|
|
Select Amplitude Modulation type |
|
|
Enable/Disable RF source state |
|
|
Set/query FM deviation |
|
|
Enable/disable frequency tone |
|
|
Set/query FM rate |
|
|
Set/query FM time interval |
|
|
Select Frequency Modulation type |
|
|
Set/query frequency mode |
|
|
Set/query the source power on port 1e |
|
|
Read the measured power port 2 |
|
|
Set/query AM modulation depth for selected pulse N |
|
|
Set/query AM width for selected pulse N |
|
|
Export the current built-in pulse item definition to the |
|
|
Set/query FM deviation for selected pulse N |
|
|
Set/query pulse rep frequency for selected pulse N. PRF is the reciprocal of PRI |
|
|
Set/query pulse rep interval for selected pulse N. PRI is the reciprocal of PRF |
|
|
Set/query pulse width on time (between the rising and falling edges) of a single pulse |
|
|
Set trigger delay value |
|
|
Query pulse type |
|
|
Select pulse type |
|
10jun2024 |
Added new topic (A.13.10) |