Stops all sweeps |
|
Automatic Fixture Removal |
Electrical Delay and Phase Offset |
|
Custom measurements |
|
Sends and queries data |
|
DIQ |
Differential IQ measurement |
Defines topology for a balanced measurement |
|
Equation Editor |
|
Time domain gating |
|
Display format |
|
Balanced measurements and Fixturing |
|
Trace Statistics |
|
Read Gain compression data |
|
Gain Compression Analysis |
|
Group Delay Aperture setting |
|
Trace Hold |
|
Limit lines for pass / fail testing |
|
Marker settings |
|
Math / Memory |
|
Measurement settings specific to a measurement number |
|
Bandwidth threshold settings |
|
Conversion parameter setting |
|
Electrical delay settings |
|
Sends and queries data |
|
Gate filter settings |
|
Trace Statistics |
|
Read Gain compression data |
|
Gain Compression Analysis |
|
Group Delay Aperture settings |
|
Limit line settings |
|
Marker settings |
|
Mag and Phase offset |
|
Balanced measurement parameter settings |
|
Ripple limit settings |
|
Spectrum Analyzer markers |
|
Smoothing settings |
|
Time domain transform settings |
|
UNCertainty |
Uncertainty trace properties |
X-Axis settings |
|
X-axis display for FCA measurements |
|
Receiver power cal (Obsolete) |
|
Mag and Phase offset |
|
Create and delete measurements |
|
Queries receiver data |
|
Point-to-point smoothing |
|
Time domain transform |
|
UNCertainty |
Uncertainty Trace Properties |
X-Axis Domain |
Controls CalPod units |
|
Interface control, ECal module state control, and Rear-panel connector control. |
|
Control the E5092A Configurable Multiport Test Set. |
|
Work with a Cal Set without having to select it into that channel. |
|
Display settings |
|
Format for data transfer |
|
Hardcopy printing |
|
Continuous or manual triggering |
|
LXI communications |
|
Saves and recalls instrument states |
|
Turns RF power ON and OFF |
Sweep Averaging |
|
IF Bandwidth |
|
Returns measurement class name |
|
Calibration and other correction settings |
|
| CKIT |
Manage Cal Kits and ECal modules |
Edit Cal Kit definitions |
|
Perform Guided Cals |
|
| COLL:SESSion |
Perform SMC and VMC calibrations |
| CSET |
Manage Cal Sets |
Port Extensions |
|
| IMD |
Controls IMD and IMDx calibration |
Chopped or Alternate sweep |
|
Ecal user characterization |
|
Frequency Offset (opt 080) |
|
Construct a segment table |
|
Frequency sweep settings |
|
Gain Compression App (opt 086) |
|
FCA measurements (opts S93082A and S93083A) |
|
MIXer Embed LO |
Allows measurements of mixers with embedded LO |
Configures mixer segments |
|
Controls external test sets |
|
NOISe |
Noise Figure (opt 028 / 029) |
Provides access to hardware configuration |
|
Receiver attenuation and overpower protection |
|
ROLE |
Assign sources to roles |
Returns the source of the reference oscillator |
|
Segment sweep settings |
|
Sweep types |
|
Pulse measurements |
|
Returns the temperature on the receiver board |
|
Returns X-axis values for channel |
Source power to the DUT |
|
DC Source control |
|
Phase control (Opt S93088A) |
|
Source power calibration |
|
Receiver Leveling |
|
Reads the VNA status registers |
VNA system setting commands |
|
Manage active channel/measurement |
|
| CAL:All |
Calibrate All Channels |
Reads various capabilities of the analyzer |
|
| CHANnels |
Perform channel operations |
Controls and queries PNA settings |
|
Configure external devices |
|
Configures external SMU, DC Meter, and DC Source properties |
|
Configures external Power Meter as Receiver |
|
| CORR:INTerpolate:LINear |
Linear interpolation |
| FIFO |
Controls data in and out of FIFO data buffer |
VNA Preferences |
|
Dynamic Uncertainty |
Trigger measurements |