LTE TDD Mode (Option 372) Commands - Requires SA and GPS


In this topic:

See Also

- Commands that are Common to All Modes

- Correction Methods Explained

- New Programming Commands

- Status Registers

Data

Returns a set of values with GPS information.

LTETdd:DATA:GPS?

Returns a set of values without GPS information.

LTETdd:DATA?

Display

Sets the trace data type (RSRP | RSRQ |RSSI | PSS | SSS | SINR )

DISPlay:LTETdd:TRACe:DATA

Sets the bar chart display color coding scheme.

DISPlay:LTETdd:WINDow[:SELect]

Sets the bar chart color coding scheme.

DISPlay:LTETdd:WINDow<n>:BCHart:CCODing

Set and query the component carrier (cc).

DISPlay:LTETdd:WINDow<n>:CCARrier  

Set the window trace type (Table, Bar Chart, Spectrum, Strip Chart).

DISPlay:LTETdd:WINDow<n>:DATA

Sets the PCI filter value of the results displayed in the window

DISPlay:LTETdd:WINDow<n>:PCI

Set and query the PCI mode of the results displayed in the window.

DISPlay:LTETdd:WINDow<n>:PCI:MODe

Sets the order of the data sorting (AUTO  | UP | DOWN)

DISPlay:LTETdd:WINDow<n>:SORT:DATA

Sets the type of data being sorted (RSRP | RSRQ |RSSI | PSS | SSS | SINR )

DISPlay:LTETdd:WINDow<n>:SORT:ORDer

Set the selected window state.

DISPlay:LTETdd:WINDow<n>:STATe

Favorites List

Set the current channel and band to a favorites setup

[:SENSe]:LTETdd:CCARrier:LIST[1]|2|3|4|5:ADD  

Query the band in the current selected favorites setup

[:SENSe]:LTETdd:CCARrier:LIST[1]|2|3|4|5:BAND?

Query the channel in the current selected favorites setup

[:SENSe]:LTETdd:CCARrier:LIST[1]|2|3|4|5:CHANnel?

Remove the current channel and band favorites setup

[:SENSe]:LTETdd:CCARrier:LIST[1]|2|3|4|5:REMove

Apply a favorites setup--band and channel--to a measurement

[:SENSe]:LTETdd:CCARrier[1]|2|3|4|5:LIST[1]|2|3|4|5:APPLy

Frequency / Carrier

Set and query the frequency error threshold

[:SENSe]:LTETdd:FERRor:THReshold   

Set and query the extended frequency lock

[:SENSe]:LTETdd:FLRange:EXTended

Set and query the component carrier band

[:SENSe]:LTETdd:CCARrier[1]|2|3|4|5:BAND   

Set and query the component carrier channel

[:SENSe]:LTETdd:CCARrier[1]|2|3|4|5:CHANnel   

Set and query the selected carrier

[:SENSe]:LTETdd:CCARrier[1]|2|3|4|5:ENABle

Set and query the center frequency of each component carrier (CC)

[:SENSe]:LTETdd:CCARrier[1]|2|3|4|5:FREQuency:CENTer

Set and query the component carrier mode (CHANnel | FREQuency)

[:SENSe]:LTETdd:CCARrier[1]|2|3|4|5:MODE

Scale / Units

Auto Scale the bar chart scan data

DISPlay:LTETdd:BCHart:Y[:SCALe]:AUTO

Set and query the per division value of the Bar Graph data

DISPlay:LTETdd:BCHart:Y[:SCALe]:PDIVision

Set and query the Bar Chart reference value

DISPlay:LTETdd:BCHart:Y[:SCALe]:RLEVel

Auto Scale the Strip chart scan data

DISPlay:LTETdd:SCHart:Y[:SCALe]:AUTO

Set and query the per division value of the Strip Chart data

DISPlay:LTETdd:SCHart:Y[:SCALe]:PDIVision

Set and query the Strip Chart reference valuef

DISPlay:LTETdd:SCHart:Y[:SCALe]:RLEVel

Auto Scale the Spectrum chart scan data

DISPlay:LTETdd:SPECtrum:Y[:SCALe]:AUTO

Set and query the per division value of the Spectrum data

DISPlay:LTETdd:SPECtrum:Y[:SCALe]:PDIVision

Set and query the Spectrum reference value

DISPlay:LTEFdd:SPECtrum:Y[:SCALe]:RLEVel

Set and query the reference position of the Spectrum trace

DISPlay:LTETdd:SPECtrum:Y[:SCALe]:RPOSition

Alignments (InstAlign)

Align all now (coupled to all individual alignments)

[:SENSe]:ALIGnment:ALL:NOW

Align all state (coupled to all individual alignments)

[:SENSe]:ALIGnment:ALL[:STATe]

Align now

[:SENSe]:ALIGnment:AMPLitude:NOW

InstAlign state

[:SENSe]:ALIGnment:AMPLitude[:STATe]

Power

Executes Auto-Range

[:SENSe]:POWer[:RF]:ARANge

Set the RF attenuator value manually

[:SENSe]:POWer[:RF]:ATTenuation

Set the RF attenuator to Auto

[:SENSe]:POWer[:RF]:ATTenuation:AUTO

Set the external Gain

[:SENSe]:POWer[:RF]:EXTGain

Enable or disable the Gain state

[:SENSe]:POWer[:RF]:GAIN[:STATe]

Set the absolute power level

[:SENSe]:POWer[:RF]:RLEVel

Set the red bar chart limit

[:SENSe]:POWer[:RF]:RPLevel

Set the blue bar chart limit

[:SENSe]:POWer[:RF]:BPLevel

Trigger Settings

Auto trigger time

TRIGger[:SEQuence]:ATRigger

Auto trigger ON/OFF

TRIGger[:SEQuence]:ATRigger:STATe

Trigger Slope (Pos/Neg)

TRIGger[:SEQuence]:EXTernal:SLOPe

Trigger Delay

TRIGger[:SEQuence]:EXTernal:DELay

Trigger Delay ON/OFF

TRIGger[:SEQuence]:EXTernal:DELay:STATe

Trigger Type (Ext/Freerun)

TRIGger[:SEQuence]:SOURce

Frequency Extender Head

Sets frequency converter corrections to "Auto" or "Edit SA"

SYSTem:HEAD:CORRections:ASETup

Shares frequency extender head corrections from SA mode

SYSTem:HEAD:CORRections[:STATe]

Enables/disables the high sensitivity state.

SYSTem:HEAD:HIGHsense[:STATe]

Sets the LO power for any installed OML head

SYSTem:HEAD:POWer

Enables/disables the frequency extender.

SYSTem:HEAD[:STATe]

Selects a frequency extender head file to load.

MMEM:LOAD:HEAD

Data Logging / Playback Actions

Enable or disable the log file auto-save

DLOGgin:FILE:ASAVe

Sets the data log file save/recall folder location

DLOGging:FILE:FOLDer

Sets the log file save type

DLOGging:FILE:TYPe

Resume playback

DLOGging:PLAYback:PAUSe

Sets the position number of component carrier manually, when paused.

DLOGging:PLAYback:POSition

Play

DLOGging:PLAYback:STARt

Stop playback

DLOGging:PLAYback:STOP

Sets the data log playback state

DLOGging:PLAYback[:STATe]

Pause

DLOGging:RECord:PAUSe

Record

DLOGging:RECord:STARt

Stop recording

DLOGging:RECord:STOP

Query the state

DLOGging:RECord[:STATe]?

Sets the position number of component carrier automatically, when paused.

RECPlayback:ACTion:POSition:AUTO

Save (.kml or .csv)

RECPlayback:ACTion:SAVE

Record/Playback Configuration

Sets the device type storage location (INTernal | USB | SD)

RECPlayback:CONFig:FILE:DEVice

Enables/Disables overwrite data filename

RECPlayback:CONFig:FILE:OWRite

Sets the data storage type (KML | CSV)

RECPlayback:CONFig:FILE:TYPE

Set the recording distance interval

DLOGing:INTerval:DISTance

Enables/Disables the measurement interval requirement for saving records

DLOGging:INTerval[:ENABled

Set and query time interval in seconds

DLOging:INTerval:TIME

Sets the measurement interval for saving records (TIME | DISTance)

DLOGing:INTerval:TYPE

USB Triaxial Antenna

Set and query the antenna's angle of azimuth reference value

[:SENSe]:ANTenna:ANGLe:AZImuth:REFerence

Set and query the antenna's angle of azimuth start value

[:SENSe]:ANTenna:ANGLe:AZImuth:STARt

Set and query the antenna's angle of azimuth step value

[:SENSe]:ANTenna:ANGLe:AZImuth:STEP

Set and query the antenna's angle of azimuth stop value

[:SENSe]:ANTenna:ANGLe:AZImuth:STOP

Set and query the elevation angle reference value

[:SENSe]:ANTenna:ANGLe:ELEVation:REFerence

Set and query the antenna's angle of elevation start value

[:SENSe]:ANTenna:ANGLe:ELEVation:STARt

Set and query the antenna's angle of elevation step value

[:SENSe]:ANTenna:ANGLe:ELEVation:STEP

Set and query the antenna's angle of elevation stop value

[:SENSe]:ANTenna:ANGLe:ELEVation:STOP

Sets the current azimuth angle

[:SENSe]:ANTenna:ANGLe:INDex:X

Sets the current elevation angle

[:SENSe]:ANTenna:ANGLe:INDex:Y

Sets the North angle on compass

[:SENSe]:ANTenna:COMPass:NORth

Display size of Polar graph and trace

[:SENSe]:ANTenna:DISPlay:POLar:ANGle

Sets the Polar display background image (i.e., if image loaded)

[:SENSe]:ANTenna:DISPlay:POLar:BACKground:IMAGe:STATe

Sets the display compass on the polar display

[:SENSe]:ANTenna:DISPlay:POLar:COMPass:IMAGe:STATe

Sets the display size of the Polar graph and trace

[:SENSe]:ANTenna:DISPlay:POLar:TYPe

Sets the antenna center frequency

[:SENSe]:ANTenna:FREQuency

Query the last measured point

[:SENSe]:ANTenna:RESult?

IMPort Import antenna correction factors from USB antenna.

SYSTem:ANTenna:USB:IMPort

Sets the antenna orientation

SYSTem:ANTenna:USB:AXIS

Sets antenna type

SYSTem:ANTenna:USB:TYPe

Presets the antenna

SYSTem:PRESet:ANTenna

Sweep

Enables/disables continuous sweep

INITiate:CONTinuous

Restarts the trace averaging

INITiate:RESTart

MMEMory comands - related to LTE FDD

Save a file to the default folder

:MMEMory:STORe:FDATa

Load a *.csv or *.kml from an OTA recorder folder

:MMEMory:LOAD:DLOG


Last Modified:

01dec2020

New mode (A12.2x)