NA Mode Commands

In this topic:

Traces

Description	Commands
Create Measurement	CALCulate:PARameter{1:4}:DEFine
Set and read number of traces	CALCulate:PARameter:COUNt
Select Measurement	CALCulate:PARameter{1:4}:SELect
Set trace format	CALCulate[:SELected]:FORMat
Multi-trace Configurations	DISPlay:WINDow:SPLit
Perform measurement conversion	CALCulate[:SELected]:CONVersion:FUNCtion

Sweep Settings

Set center freq	[:SENSe]:FREQuency:CENTer
Set freq span	[:SENSe]:FREQuency:SPAN
Set start freq	[:SENSe]:FREQuency:STARt
Set stop freq	[:SENSe]:FREQuency:STOP
Read X-axis values	[:SENSe]:FREQuency:DATA?
Set resolution (number of points)	[:SENSe]:SWEep:POINts
Set sweep time	[:SENSe]:SWEep:TIME
Read sweep time	[:SENSe]:SWEep:MTIMe?
Set manual source power	SOURce:POWer
Set flat source power	SOURce:POWer:ALC[:MODE]
Set trigger Internal or External	TRIGger:SOURce
Set polarity of external	TRIGger:SLOPe

IFBW / Average / Smooth / Image Rej

IFBW	[:SENSe]:BandWIDth
Averaging	[:SENSe]:AVERage:COUNt
Clear Averaging	[:SENSe]:AVERage:CLEar
Average (Swp/Point)	[:SENSe]:AVERage:MODE
Smoothing ON/OFF	CALCulate[:SELected]:SMOothing[:STATe]
Smoothing aperture	CALCulate[:SELected]:SMOothing:APERture

Display Items

View Memory trace	DISPlay:WINDow:TRACe:MEMory:STATe
View Data trace	DISPlay:WINDow:TRACe:STATe
Scaling - auto	DISPlay:WINDow:TRACe:Y[:SCALe]:AUTO
Scaling - Set bottom of scale	DISPlay:WINDow:TRACe:Y[:SCALe]:BOTTom
Scaling - Set per division	DISPlay:WINDow:TRACe:Y[:SCALe]:PDIVision
Scaling - Set reference level	DISPlay:WINDow:TRACe:Y[:SCALe]:RLEVel
Scaling - Set reference position	DISPlay:WINDow:TRACe:Y[:SCALe]:RPOSition
Scaling - Set top of scale	DISPlay:WINDow:TRACe:Y[:SCALe]:TOP
Electrical Delay	CALCulate[:SELected]:CORRection:EDELay:TIME
Phase Offset	CALCulate[:SELected]:CORRection:OFFSet:PHASe
Mag Offset	CALCulate[:SELected]:OFFSet[:MAGNitude]
Mag Slope	CALCulate[:SELected]:OFFSet:SLOPe

Limit Lines

Limit line beep	CALCulate[:SELected]:LIMit:SOUNd
Create limit lines	CALCulate[:SELected]:LIMit:LLData
Limit line testing state	CALCulate[:SELected]:LIMit[:STATe]
Limit line testing annotation	CALCulate[:SELected]:LIMit:WARN
Read Pass / Fail	STATus:QUEStionable:LIMit:CONDition?
Build Limit from Trace	None

Markers

Marker On/Off	CALCulate[:SELected]:MARKer[:STATe]
Activate a marker	CALCulate[:SELected]:MARKer:ACTivate
Markers - all off	CALCulate[:SELected]:MARKer:AOFF
Read BW data	CALCulate[:SELected]:MARKer:BWIDth:DATA
Marker search - BW / Q On/Off	CALCulate[:SELected]:MARKer:BWIDth[:STATe]
Markers - coupled	CALCulate[:SELected]:MARKer:COUPled
BW search value	CALCulate[:SELected]:MARKer:FUNCtion:BWIDth:THReshold
Marker search - Max	CALCulate[:SELected]:MARKer:FUNCtion:MAXimum
Marker search - Min	CALCulate[:SELected]:MARKer:FUNCtion:MINimum
Marker search - MAX between Markers 1,2 (M5) or Markers 3,4 (M6)	CALCulate[:SELected]:MARKer:FUNCtion:Mn:MAX
Marker search - MIN between Markers 1,2 (M5) or Markers 3,4 (M6)	CALCulate[:SELected]:MARKer:FUNCtion:Mn:MIN
Marker search - Peak excursion	CALCulate[:SELected]:MARKer:FUNCtion:PEXCursion
Marker search - Peak Next	CALCulate[:SELected]:MARKer:FUNCtion:PNEXt
Marker search - Peak threshold	CALCulate[:SELected]:MARKer:FUNCtion:PTHReshold
Marker search - Target	CALCulate[:SELected]:MARKer:FUNCtion:TARGet
Marker search - Wrap/No Wrap	CALCulate[:SELected]:MARKer:FUNCtion:TDIRection
Tracking On/Off	CALCulate[:SELected]:MARKer:FUNCtion:TRACking
FieldFox setting => to marker location	CALCulate[:SELected]:MARKer:SET
Marker format	CALCulate[:SELected]:MARKer:FORMat
Marker => specified trace	CALCulate[:SELected]:MARKer:TRACe
Marker => specified X-axis location	CALCulate[:SELected]:MARKer:X
Read Marker Y-axis location	CALCulate[:SELected]:MARKer:Y?

Big Marker Display States (A and B)

Enable Big marker readouts	DISPlay:MARKer:LARGe:STATe
Set font size	DISPlay:MARKer:LARGe:<x>:FONT
Set how the marker is displayed (norm / delta)	DISPlay:MARKer:LARGe:<x>:DEFine:LINE<n>:MARKer:STATe
Enable a readout line	DISPlay:MARKer:LARGe:<x>:DEFine:LINE<n>:STATe
Assign a marker number to the readout line	DISPlay:MARKer:LARGe:<x>:DEFine:LINE<n>:MNUMber
Assign a trace number to the readout line	DISPlay:MARKer:LARGe:<x>:DEFine:LINE<n>:TNUMber
Set format for the readout line	DISPlay:MARKer:LARGe:<x>:DEFine:LINE<n>:FORMat
Set marker tracking	DISPlay:MARKer:LARGe:<x>:DEFine:LINE<n>:TRACking
Set number of traces	DISPlay:MARKer:LARGe:<x>:TRACE:COUNt
Set measurement for the trace	DISPlay:MARKer:LARGe:<x>:DEFine:TRACe<n>:MEASurement
Set format for the trace	DISPlay:MARKer:LARGe:<x>:DEFine:TRACe<n>:FORMat
Enable bandwidth search	DISPlay:MARKer:LARGe:<x>:DEFine:TRACe<n>:BWIDth:STATe

Math

Math function

CALCulate[:SELected]:MATH:FUNCtion

Save / Recall Files - Data

Save data trace to csv file	MMEMory:STORe:FDATa
Save SNP data	MMEMory:STORe:SNP[:DATA]
See other Save / Recall commands

Send and read formatted measured data	CALCulate[:SELected]:DATA:FDATa
Send and read formatted memory data	CALCulate[:SELected]:DATA:FMEM
Send and read unformatted measured data	CALCulate[:SELected]:DATA:SDATa
Send and read unformatted memory data	CALCulate[:SELected]:DATA:SMEM
Set read format	FORMat[:DATA]

Port Extensions

Enable	[:SENSe]:CORRection:EXTension[:STATe]
Set port 1	[:SENSe]:CORRection:EXTension:PORT1
Set port 2	[:SENSe]:CORRection:EXTension:PORT2
Set velocity factor	[:SENSe]:CORRection:RVELocity:COAX

Calibration

See Also

Correction Methods Explained

Calibration Examples

Set and read error term data	[:SENSe]:CORRection:COEFficient[:DATA]
Read number of cal steps	[:SENSe]:CORRection:COLLect:GUIDed:SCOunt
Measure step number	[:SENSe]:CORRection:COLLect:GUIDed:STEP:ACQuire
Prompt for step number	[:SENSe]:CORRection:COLLect:GUIDed:STEP:PROMpt
Measure Quick Cal	[:SENSe]:CORRection:COLLect[:ACQuire]:INT
Measure load	[:SENSe]:CORRection:COLLect[:ACQuire]:LOAD
Measure open	[:SENSe]:CORRection:COLLect[:ACQuire]:OPEN
Measure short	[:SENSe]:CORRection:COLLect[:ACQuire]:SHORt
Measure thru	[:SENSe]:CORRection:COLLect[:ACQuire]:THRU
Set Cal Kit	[:SENSe]:CORRection:COLLect:CKIT:LABel
Catalog all cal kits	[:SENSe]:CORRection:COLLect:CKIT:LABel:CATalog?
Set connectors	[:SENSe]:CORRection:COLLect:CONNector
Select method - Enhanced Response	[:SENSe]:CORRection:COLLect:METHod:ERES
Select method - QuickCal	[:SENSe]:CORRection:COLLect:METHod:QCALibrate:CALibrate
Select method - QuickCal Enhanced Response	[:SENSe]:CORRection:COLLect:METHod:QCALibrate:ERESponse
Select method - Simple Open response	[:SENSe]:CORRection:COLLect:METHod[:RESPonse]:OPEN
Select method - Simple Short response	[:SENSe]:CORRection:COLLect:METHod[:RESPonse]:SHORt
Select method - Thru response	[:SENSe]:CORRection:COLLect:METHod[:RESPonse]:THRU
Select method - Open response	[:SENSe]:CORRection:COLLect:METHod:ORESponse
Select method - Short response	[:SENSe]:CORRection:COLLect:METHod:SRESponse
Select method - 1-port SOLT	[:SENSe]:CORRection:COLLect:METHod:SOLT1
Select method - TRL	[:SENSe]:CORRection:COLLect:METHod:TRL
Read method	[:SENSe]:CORRection:COLLect:METHod:TYPE?
Set AutoOrient for ECal	[:SENSe]:CORRection:COLLect:ECAL:AORient
Set simple ECal	[:SENSe]:CORRection:COLLect:ECAL:SIMPle
Omit Isolation	[:SENSe]:CORRection:COLLect:OISolation
Select Medium	[:SENSe]:CORRection:MEDium
Sets Start & Stop frequencies to calibration cardinal points	[:SENSe]:CORRection:APPLy:NEARest
Set Waveguide cutoff	[:SENSe]:CORRection:WGCutoff
Finish Cal	[:SENSe]:CORRection:COLLect:SAVE
Turn ALL Correction ON and OFF	[:SENSe]:CORRection[:STATe]
Turn User Correction ON and OFF	[:SENSe]:CORRection:USER[:STATe]
Set system impedance	[:SENSe]:CORRection:IMPedance[:INPut][:MAGNitude]
Set CalReady type	[:SENSe]:CORRection:CALReady:TYPE

Source

Set the active source

SOURce{1:1}:PORT[:STATe]

Time Domain (Opt 010)

Enable	CALCulate[:SELected]:TRANsform:TIME:STATe
Start time	CALCulate[:SELected]:TRANsform:TIME:STARt
Stop time	CALCulate[:SELected]:TRANsform:TIME:STOP
Center time	CALCulate[:SELected]:TRANsform:TIME:CENTer
Span time	CALCulate[:SELected]:TRANsform:TIME:SPAN
Lowpass or BandPass	CALCulate[:SELected]:TRANsform:TIME: [TYPE]
Step or Impulse	CALCulate[:SELected]:TRANsform:TIME:STIMulus
Step rise time	CALCulate[:SELected]:TRANsform:TIME:STEP:RTIMe
Impulse width	CALCulate[:SELected]:TRANsform:TIME:IMPulse:WIDTh
Kaiser Bessel width	CALCulate[:SELected]:TRANsform:TIME:KBESsel
Set Lowpass freq.	CALCulate[:SELected]:TRANsform:TIME:LPFREQuency

Time Domain Gating

Enable	CALCulate[:SELected]:FILTer[:GATE]:TIME:STATe
Start time	CALCulate[:SELected]:FILTer[:GATE]:TIME:STARt
Stop time	CALCulate[:SELected]:FILTer[:GATE]:TIME:STOP
Center time	CALCulate[:SELected]:FILTer[:GATE]:TIME:CENTer
Span time	CALCulate[:SELected]:FILTer[:GATE]:TIME:SPAN
Gating shape	CALCulate[:SELected]:FILTer[:GATE]:TIME:SHAPe
Bandpass or notch	CALCulate[:SELected]:FILTer[:GATE]:TIME

Last Modified:

01june2022	Added SENS:CORR:APPL:NEAR command (A12.5x)
13-Nov-2013	Added TRL command
6-Mar-2013	Added new commands (A.06.25)
18-Oct-2012	Added new commands (A.06.00)