SA Mode Commands

Description

Command

Center freq

[:SENSe]:FREQuency:CENTer

Step size for up/down keys

[:SENSe]:FREQuency:CENTer:STEP

Step size auto/manual

[:SENSe]:FREQuency:CENTer:STEP:AUTO

Freq span

[:SENSe]:FREQuency:SPAN

Span to full

[:SENSe]:FREQuency:SPAN:FULL

Span to zero

[:SENSe]:FREQuency:SPAN:ZERO

Start freq

[:SENSe]:FREQuency:STARt

Stop freq

[:SENSe]:FREQuency:STOP

Frequency annotation method

[:SENSe]:FREQuency:ANNotation[:SELect]

Channel number center

[:SENSe]:RADio:CHANnel:CENTer

Uplink or Downlink

[:SENSe]:RADio:CHANnel:DIRection

Start channel

[:SENSe]:RADio:CHANnel:STARt

Channel step size

[:SENSe]:RADio:CHANnel:STEP

Stop channel

[:SENSe]:RADio:CHANnel:STOP

Select standard

[:SENSe]:RADio:STANdard[:SELect]

Freq or Chan

[:SENSe]:RADio:TEUNit

Attenuation value

[:SENSe]:POWer[:RF]:ATTenuation

Atten Auto/Manual

[:SENSe]:POWer[:RF]:ATTenuation:AUTO

Set external gain value

[:SENSe]:POWer[:RF]:EXTGain

Preamp ON/OFF

[:SENSe]:POWer[:RF]:GAIN[:STATe]

Read number of traces.

[:SENSe]:QUANtity:TACTive?

Enable /Disable Baseband

[:SENSe]:PATH: BBANd

Enable/disable the Baseband 1 preamp gain reduction (≤15 MHz)

[:SENSe]:BBANd:BP1Gain:REDuce

Enable/disable the Baseband 2 preamp gain reduction (>15 MHz)

[:SENSe]:BBANd:BP2Gain:REDuce

Sweep time (Non-zero span)

[:SENSe]:SWEep:ACQuisition

Sweep time (Zero span)

[:SENSe]:SWEep:TIME

Read sweep time

[:SENSe]:SWEep:MTIMe?

Auto / Manual

[:SENSe]:SWEep:ACQuisition:AUTO

Sweep points

[:SENSe]:SWEep:POINts

Sweep Type

[:SENSe]:SWEep:TYPe

Reverse sweep (Step sweep and Opt. 209 only)

[:SENSe]:FREQuency:SPAN:DREVerse

Auto Scale trace

DISPlay:WINDow:TRACe:Y[:SCALe]:AUTO

Per division

DISPlay:WINDow:TRACe:Y[:SCALe]:PDIVision

Reference level

DISPlay:WINDow:TRACe:Y[:SCALe]:RLEVel

Reference position

DISPlay:WINDow:TRACe:Y[:SCALe]:RPOSition

Log / Linear scale

[:SENSe]:AMPLitude:SCALe

Set Units

[:SENSe]:AMPLitude:UNIT

Read ONLY - Bottom scale value

DISPlay:WINDow:TRACe{1:4}:Y[:SCALe]:BOTTom

Read ONLY - Top scale value

DISPlay:WINDow:TRACe{1:4}:Y[:SCALe]:TOP

Average count

[:SENSe]:AVERage:COUNt

Averaging type

[:SENSe]:AVERage:TYPE

Restart trace averaging

INITiate:RESTart

Manual Res BW value

[:SENSe]:BANDwidth[:RESolution]

Choose Auto or Manual Res BW

[:SENSe]:BANDwidth[:RESolution]:AUTO

Manual Video BW value

[:SENSe]:BANDwidth:VIDeo

Choose Auto or Manual Video BW

[:SENSe]:BANDwidth:VIDeo:AUTO

IF Output

[:SENSe]:BANDwidth:IF:OUT

Set Trace Type

TRACe{1:4}:TYPE

Returns the current trace X-values

TRACe{1:4}:XVALue

Detector function

[:SENSe]:DETector:FUNCtion

Multiple Detectors

Align all now (coupled to all individual alignments)

[:SENSe]:ALIGnment:AMPLitude:NOW

Align all state (coupled to all individual alignments)

[:SENSe]:ALIGnment:ALL[:STATe]

Align now

[:SENSe]:ALIGnment:AMPLitude[OBSOLETE]:NOW

InstAlign state

[:SENSe]:ALIGnment:AMPLitude[:STATe]

RF burst now (Not applicable to ERTA)

[:SENSe]:ALIGnment:BURSt:NOW

RF burst state (Not applicable to ERTA)

[:SENSe]:ALIGnment:BURSt[:STATe]

Fast channel equalization alignment (enable/disable)

[:SENSe]:ALIGnment:CHEQ:FAST

Channel equalization now

[:SENSe]:ALIGnment:CHEQ:NOW

Channel equalization state

[:SENSe]:ALIGnment:CHEQ[:STATe]

Query a file catalog

:INSTrument:CATalog?

Enables front panel key press control

:INSTrument:GTL

Disables front panel key press control (Lockout)

:INSTrument:GTR

Set and query the status of the remote SCPI lockout

:INSTrument:RLOCkout:DISable

Sets the current mode

:INSTrument[:SELect]

Limit line beep

CALCulate[:SELected]:LIMit:SOUNd

Create limit lines

CALCulate:LIMit:LLData

Limit line testing state

CALCulate:LIMit[:STATe]

Limit line testing annotation

CALCulate:LIMit:WARN

Display Line level setting

DISPlay:WINDow:TRACe:Y:DLINe

Display Line state

DISPlay:WINDow:TRACe:Y:DLINe:STATe

Read Pass/Fail

STATus:QUEStionable:LIMit:CONDition?

Build Limit from Trace

None

Sets the Precision Marker value

CALCulate:MARKer:FCOunt:PRECision

Select a marker

CALCulate:MARKer:ACTivate

Markers - all off

CALCulate:MARKer:AOFF

Audio Beep on Marker

CALCulate:MARKer:AUDio:BEEP

Markers - Fixed delta reference marker state.

CALCulate:MARKer:DREF:FIXed

Frequency counter marker ON/OFF

CALCulate:MARKer:FCOunt[:STATe]

Read Frequency Count

CALCulate:MARKer:FCOunt:X?

Set Noise Marker and Band Power Marker

CALCulate:MARKer:FUNCtion

Band power span

CALCulate:MARKer:FUNCtion:BAND:SPAN

Band power mode

CALCulate:MARKer:FUNCtion:BAND:SPAN:AUTO

Interval power span

CALCulate:MARKer:FUNCtion:INTerval:SPAN

Interval power mode

CALCulate:MARKer:FUNCtion:INTerval:SPAN:AUTO

Marker search - Max

CALCulate:MARKer{1:6}:FUNCtion:MAXimum

Marker search - Min

CALCulate:MARKer{1:6}:FUNCtion:MINimum

Marker search - Peak excursion

CALCulate:MARKer{1:6}:FUNCtion:PEXCursion

Marker search - Peak left

CALCulate:MARKer{1:6}:FUNCtion:PLEFt

Marker search - Peak Next

CALCulate:MARKer{1:6}:FUNCtion:PNEXt

Marker search - Peak right

CALCulate:MARKer{1:6}:FUNCtion:PRIGht

Marker search - Peak threshold

CALCulate:MARKer{1:6}:FUNCtion:PTHReshold

Noise marker On/Off

CALCulate:MARKer:NOISe[:STATe]

Marker -> Setting

CALCulate:MARKer:SET

Move marker to center freq

CALCulate:MARKer:SET:CENTer

Move marker to ref level

CALCulate:MARKer:SET:REFLevel

Signal Tracking

CALCulate:MARKer:STRack

Marker On/Off

CALCulate:MARKer[:STATe]

Move marker to other trace

CALCulate:MARKer:TRACe

Move/read marker X-axis position

CALCulate:MARKer:X

Read marker Y-axis position

CALCulate:MARKer:Y?

Read Trace Data

TRACe{1:4}:DATA

Saves trace to CSV file.

MMEMory:STORe:FDATa

CW or S/R

SOURce:MODE

CW Frequency

SOURce:FREQuency[:CW]

Normalize

SOURce:NORMalize

Power Level (All models EXCEPT N9912A)

SOURce:POWer

Max Power (All models EXCEPT N9912A)

SOURce:POWer:MAXimum

Attenuation (power) N9912A ONLY

SOURce:POWer:ATTenuation

Enable Source Tracking

SOURce:TRACking

All corrections OFF

[:SENSe]:AMPLitude:CORRections:DISable

All corrections ON

[:SENSe]:AMPLitude:CORRections[:STATe] (SUPERSEDED)

Enable

SOURce:TOFFset:ENABle

Set frequency

SOURce:TOFFset:FREQuency

Reverse frequency

SOURce:TOFFset:REVerse

Antenna corrections ON

[:SENSe]:AMPLitude:CORRections:ANTenna[:STATe]

Cable corrections ON

[:SENSe]:AMPLitude:CORRections:CABLe[:STATe]

Load Antenna file

MMEMory:LOAD:ANTenna

Store Antenna file

MMEMory:STORe:ANTenna

Clear Antenna correction values

[:SENSe]:AMPLitude:CORRections:ANTenna:DEFault

Load Cable file

MMEMory:LOAD:CABLe

Store Cable file

MMEMory:STORe:CABLe

Clear Cable correction values

[:SENSe]:AMPLitude:CORRections:CABLe:DEFault

Antenna corrections ON

[:SENSe]:AMPLitude:CORRections:SANTenna[:STATe]

Cable corrections ON

[:SENSe]:AMPLitude:CORRections:SCABle[:STATe]

Load Antenna file

MMEMory:LOAD:SANTenna

Store Antenna file

MMEMory:STORe:SANTenna

Clear Antenna correction values

[:SENSe]:AMPLitude:CORRections:SANTenna:DEFault

Load Cable file

MMEMory:LOAD:SCABle

Store Cable file

MMEMory:STORe:SCABle

Clear Cable correction values

[:SENSe]:AMPLitude:CORRections:SCABle:DEFault

Trigger Type (Ext/Vid/RFBurst/Freerun/Periodic)

TRIGger[:SEQuence]:SOURce

Trigger Slope (Pos/Neg)

TRIGger[:SEQuence]:SLOPe

Trigger Delay

TRIGger[:SEQuence]:DELay

Trigger Delay ON/OFF

TRIGger[:SEQuence]:DELay:STATe

Trigger Level

TRIGger[:SEQuence]:VIDeo:LEVel

Auto trigger time

TRIGger[:SEQuence]:ATRigger

Auto trigger ON/OFF

TRIGger[:SEQuence]:ATRigger:STATe

Trigger Position

TRIGger[:SEQuence]:POSition

Trigger Position ON/OFF

TRIGger[:SEQuence]:POSition:STATe

Enable gating

TRIGger[:SEQuence]:FGATe[:STATe]

Set gate delay

TRIGger[:SEQuence]:FGATe:DELay

Display the gating window

TRIGger[:SEQuence]:FGATe:VIEW[:STATe]

Set X-axis time span for the gating window

TRIGger[:SEQuence]:FGATe:VIEW:TIME

Set the width of the gated area within the gating window

TRIGger[:SEQuence]:FGATe:WIDTh

Sets/query the audio capture count value

[:SENSe]:AUDio:CAPTure:COUNt

Sets/query the automatic loading of audio capture file

[:SENSe]:AUDio:CAPTure:PLAYback:ALOad

Start the audio capture file playback

[:SENSe]:AUDio:CAPTure:PLAYback:STARt

Stop the audio capture file playback

[:SENSe]:AUDio:CAPTure:PLAYback:STOP

Sets/query the audio capture fm stereo type

[:SENSe]:AUDio:CAPTure:PLAYback:SCHannel

Start the audio capture

[:SENSe]:AUDio:CAPTure:STARt

Stop the audio capture

[:SENSe]:AUDio:CAPTure:STOP

Set/query the audio capture time

[:SENSe]:AUDio:CAPTure:TIME

Set/query the AM window top Y axis percentage

[:SENSe]:ADEMod:METRics:AMTY

Set/query the analog demod metrics type (AM/FM Narrow/FM wide)

[:SENSe]:ADEMod:METRics:DTYPe

Set/query the BPF type

[:SENSe]:ADEMod:METRics:FILTer:BPF[:TYPe]

Set/query the de-emphasis TAO value

[:SENSe]:ADEMod:METRics:FILTer:DEEMphasis:TAO

Set/query the de-emphasis state value

[:SENSe]:ADEMod:METRics:FILTer:DEEMphasis[:STATe]

Set/query the HPF cutoff value

[:SENSe]:ADEMod:METRics:FILTer:HPF:CUToff

Set/query the HPF type

[:SENSe]:ADEMod:METRics:FILTer:HPF[:TYPe]

Set/query the LPF cutoff value

[:SENSe]:ADEMod:METRics:FILTer:LPF:CUToff

Set/query the LPF cutoff type

[:SENSe]:ADEMod:METRics:FILTer:LPF[:TYPe]

Set/query the FM window top Y axis frequency

[:SENSe]:ADEMod:METRics:FMTY

Set/query the analog demod audio value (Mute/On)

[:SENSe]:ADEMod:METRics:LON

Set/query the analog demod audio listen time value

[:SENSe]:ADEMod:METRics:LTIMe

Set/query Deviation Peak+ and Peak- in the demodulation window

[:SENSe]:ADEMod:METRics:MMENable

Set/query the PM window Y axis top radian value

[:SENSe]:ADEMod:METRics:PMTY

Set/query the AM SSB window Y axis top gracticule value

[:SENSe]:ADEMod:METRics:SSBTY

Set/query the time span of the modulation window

[:SENSe]:ADEMod:METRics:STIMe

Set/query the analog demod center frequency value

[:SENSe]:ADEMod:METRics:TFReq

This command now chooses the AM/FM metrics type:

- Tune and Listen (TAL) or

- Analog Demod Metrics (ADEM)

[:SENSe]:MEASurement:ADEMod is a new SCPI syntax and is recommended.

And, the following legacy is not recommended: [:SENSe]:MEASurement:ADEMod (LEGACY BEHAVIOR)

Related Audio Capture Memory commands:

Set/query the analog demod audio file storage device type

Set/query the analog demod audio filename

Set/query the adding the timestamp to the analog demod  audio filename

Pause

RECPlayback:ACTion:PAUSe

Play

RECPlayback:ACTion:PLAY

Record

RECPlayback:ACTion:RECord

Tag position

RECPlayback:ACTion:SPOSition

Stop

RECPlayback:ACTion:STOP

Trace position

RECPlayback:ACTion:TPOSition

Frequency Mask Trigger (FMT) data

RECPlayback:CONFig:FMTRigger:LLData

FMT enable

RECPlayback:CONFig:FMTRigger:ENABle

Playback Time Interval

RECPlayback:CONFig:PRFTrace

Playback Time Interval

RECPlayback:CONFig:PRLTrace

Playback Time Interval

RECPlayback:CONFig:PTINterval

Record Segment Counting Length

RECPlayback:CONFig:RSCLength

Record Source

RECPlayback:CONFig:RSOurce

Record Time Interval

RECPlayback:CONFig:RTINerval

Record Time limit

RECPlayback:CONFig:RTLSeconds

Clear all records

RECPlayback:SESSion:CARecords

Close

RECPlayback:SESSion:CLOSe

Records single, range, or all (batch) of trace data

RECPlayback:SESSion:CSSTyle

Create new session

RECPlayback:SESSion:NEW

Open session

RECPlayback:SESSion:OPEN?

Storage device

RECPlayback:SESSion:SDEVice

Trace record limit

RECPlayback:SESSion:TRLimit

Is a session open?

STATus:OPERation:SAMode:CONDition?

Enables/disables the PSD function

[:SENSe]:AMPLitude:PSDFunction

Activate the EMF antenna

[:SENSe]:CHPower:TAASelect

All channel meas OFF

[:SENSe]:MEASurement:AOFF

Select channel meas

[:SENSe]:MEASurement:CHANnel

Select Interference Analysis (Opt 236) display.

[:SENSe]:MEASurement:INTerference

Preset channel meas

[:SENSe]:MEASurement:PRESet

Power percent for Occupied Bandwidth

[:SENSe]:OBW:PPOW

Read current channel measurement data

CALCulate:MEASurement:DATA?

Averaging ON/OFF

[:SENSe]:CMEasurement:AVERage:ENABle

Integration BW

[:SENSe]:CMEasurement:IBW

RCC filter state

[:SENSe]:CMEasurement:RRCFilter

RCC filter value

[:SENSe]:CMEasurement:RRCFilter:ALPHa

Reference value

[:SENSe]:ACPower:MREFerence

Reference method

[:SENSe]:ACPower:MREFerence:AUTO

Meas Type

[:SENSe]:ACPower:MTYPe

Limit testing On/Off

[:SENSe]:ACPower:LIMit[:STATe]

Offset bandwidths

[:SENSe]:ACPower:OFFSet:BWIDth

Offset frequencies

[:SENSe]:ACPower:OFFSet:FREQuency

Offset states

[:SENSe]:ACPower:OFFSet:STATe

Lower offset limits

[:SENSe]:ACPower:OFFSet:LLIMit

Upper offset limits

[:SENSe]:ACPower:OFFSet:ULIMit

Blue power level

[:SENSe]:SPECtrogram:BPLevel

Red power level

[:SENSe]:SPECtrogram:RPLevel

Time/Delta marker state

[:SENSe]:SPECtrogram:TMARker:STATe

Time/Delta marker location

[:SENSe]:SPECtrogram:TMARker:VALue

Spectrogram display setting

[:SENSe]:SPECtrogram:VIEW

Waterfall angle

[:SENSe]:SPECtrogram:WANGle

This command now chooses the AM/FM metrics type:

- Tune and Listen (TAL) or

- Analog Demod Metrics (ADEM)

[:SENSe]:MEASurement:ADEMod (LEGACY BEHAVIOR) is not recommended and has a new recommended behavior: [:SENSe]:MEASurement:ADEMod

Tune and Listen demod type

[:SENSe]:MEASurement:TAListen[:OBSOLETE] (see [:SENSe]:ADEMod:METRics:DTYPe)

Sets the Tune and Listen AM LSB/USB Gain

[:SENSe]:TAListen:AM:SSB:GAIN

Volume

[:SENSe]:TAListen:AVOLume - OBSOLETE

Demod ON / OFF

[:SENSe]:TAListen:DSTate

Demod type

[:SENSe]:TAListen:DTYPe

Listen tme

[:SENSe]:TAListen:LTIMe

Tune freq

[:SENSe]:TAListen:TFReq

[:SENSe]:SEMask:AVERage:COUNt

[:SENSe]:SEMask:AVERage:ENABle

Sets the Reference channel detector settings

[:SENSe]:SEMask:CDETector[:FUNCtion]              

[:SENSe]:SEMask:MTYPe       

Sets the Offset detector settings

[:SENSe]:SEMask:ODETector[:FUNCtion]               

Set the absolute start value for a segment

[:SENSe]:SEMask:OFFSet<n>:ALIMit:STARt

Set the absolute stop value for a segment

[:SENSe]:SEMask:OFFSet<n>:ALIMit:STOP

Set the absolute stop value to automatic for a segment

[:SENSe]:SEMask:OFFSet<n>:ALIMit:STOP:AUTO

Set the relative start value for a segment

[:SENSe]:SEMask:OFFSet<n>:RLIMit:STARt

Set the relative stop value for a segment

[:SENSe]:SEMask:OFFSet<n>:RLIMit:STOP

Set the relative stop value to automatic for a segment

[:SENSe]:SEMask:OFFSet<n>:RLIMit:STOP:AUTO

Set the type of triggers for the SEM failure mask

[:SENSe]:SEMask:OFFSet<n>:FMASk

[:SENSe]:SEMask:REFChannel:CENTer:AUTO

[:SENSe]:IQSTream:DHOSt

[:SENSe]:IQSTream:DPORt

Sets the IQ streaming protocol

[:SENSe]:IQSTream:PROTocol               

[:SENSe]:IQSTream:SPP

Re-sends the metadata packets

[:SENSe]:IQSTream:VITA:MRESend

[:SENSe]:IQSTream:VITA:MRIP        

[:SENSe]:IQSTream:SIDentifier

[:SENSe]:IQSTream:STARt

Stops IQ Streaming

[:SENSe]:IQSTream:STOP

In VITA streaming mode, sends metadata

[:SENSe]:IQSTream:VITA:MRESend

In VITA protocol, resends packet data

[:SENSe]:IQSTream:VITA:MRIP

In VITA protocol, sets the stream identifier

[:SENSe]:IQSTream:VITA:SIDentifier

Sets the IQ Analysis mode

[:SENSe]:MEASurement:IQANalysis

Set and query the antenna's angle of azimuth reference value

[:SENSe]:ANTenna:ANGLe:AZImuth:REFerence

Set and query the antenna's angle of azimuth start value

[:SENSe]:ANTenna:ANGLe:AZImuth:STARt

Set and query the antenna's angle of azimuth step value

[:SENSe]:ANTenna:ANGLe:AZImuth:STEP

Set and query the antenna's angle of azimuth stop value

[:SENSe]:ANTenna:ANGLe:AZImuth:STOP

Set and query the elevation angle reference value

[:SENSe]:ANTenna:ANGLe:ELEVation:REFerence

Set and query the antenna's angle of elevation start value

[:SENSe]:ANTenna:ANGLe:ELEVation:STARt

Set and query the antenna's angle of elevation step value

[:SENSe]:ANTenna:ANGLe:ELEVation:STEP

Set and query the antenna's angle of elevation stop value

[:SENSe]:ANTenna:ANGLe:ELEVation:STOP

Sets the current azimuth angle

[:SENSe]:ANTenna:ANGLe:INDex:X

Sets the current elevation angle

[:SENSe]:ANTenna:ANGLe:INDex:Y

Sets the North angle on compass

[:SENSe]:ANTenna:COMPass:NORth

Display size of Polar graph and trace

[:SENSe]:ANTenna:DISPlay:POLar:ANGle

Sets the Polar display background image (i.e., if image loaded)

[:SENSe]:ANTenna:DISPlay:POLar:BACKground:IMAGe:STATe

Sets the display compass on the polar display

[:SENSe]:ANTenna:DISPlay:POLar:COMPass:IMAGe:STATe

Sets the display size of the Polar graph and trace

[:SENSe]:ANTenna:DISPlay:POLar:TYPe

Sets the antenna center frequency

[:SENSe]:ANTenna:FREQuency

Query the last measured point

[:SENSe]:ANTenna:RESult?

Sets the antenna orientation

SYSTem:ANTenna:USB:AXIS (SUPERSEDED) is not recommended and has a new recommended behavior:

SYSTem:ANTenna:EMF:AXIS

Import antenna correction factors from USB antenna.

SYSTem:ANTenna:USB:IMPort (SUPERSEDED) is not recommended and has a new recommended behavior:

SYSTem:ANTenna:EMF:IMPort

Import antenna correction factors CSV file for EMF antenna type FSH3D

SYSTem:ANTenna:EMF:IMPort:FILe

SYSTem:ANTenna:USB:TYPe (SUPERSEDED) is not recommended and has a new recommended behavior:

SYSTem:ANTenna:EMF:TYPe

Presets the antenna

SYSTem:PRESet:ANTenna

SA Mode Frequency Converter Only:

Enable/disables frequency converter corrections of head

[:SENSe]:AMPLitude:CORRections:CONVerter:DEFault

Clears the frequency converter corrections table

[:SENSe]:AMPLitude:CORRections:CONVerter[:STATe]     

Recalls a frequency converter corrections file (*csv)

MMEMory:LOAD:CONVerter

Saves a freqeuncy converter corrections file (*csv)

MMEMory:STORe:CONVerter

All Frequency Converter Compatible Modes:

Selects a frequency extender head file to load

MMEMory:LOAD:HEAD

Sets frequency converter corrections to "Auto" or "Edit SA"

SYSTem:HEAD:CORRections:ASETup

Shares frequency extender head corrections from SA mode

SYSTem:HEAD:CORRections[:STATe]

Enables/disables the high sensitivity state

SYSTem:HEAD:HIGHsense[:STATe]

Sets the LO power for any installed OML head

SYSTem:HEAD:POWer

Enables/disables the frequency extender

SYSTem:HEAD[:STATe]

ADC Over-range status

CALCulate:MEASurement:WAOR?

Set and query ADC over range warning emphasis

SYSTem:PREFerences:SA:EAOR

Set and query the ADC over range audible beep length

SYSTem:PREFerences:SA:EAOR:BEEP

21-june-23

Updated commands (A.12.7x)

21-dec-22

Updated commands (A.12.5x)

01june2022

Updated commands (A12.4x)

01dec2020

Updated commands (A12.1x)

20apr2020

Added for A.11.75 FW (Compatible with IQA, OTA, PAA, RTSA, & SA Modes)

01dec2019

Added new commands (A.11.5x)

19apr2019

Added new commands (A11.25)

19-sep-2016

Corrected/Added SA reverse sweep SCPI command (step sweep only). (:FREQ:SPAN:DREV)

25-Mar-2014

Added new commands (A.06.25)

25-Mar-2014

Added new commands (A.06.00)